Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM3090E _53 Suspension _008765 REAR SUSPENSION _0049365 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 89408C 2.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)

Hide 42312B 3.REMOVE REAR AXLE SHAFT NUT LH (for 4WD/AWD)

C130587

a.

Using SST and a hammer, unstake the staked part of the rear axle shaft nut.

SST
09930-00010  (09931-00010, 09931-00020)

NOTICE:

Loosen the staked part of the rear axle shaft nut completely, otherwise the screw of the drive shaft may be damaged.



b.

While applying the brakes, remove the rear axle shaft nut.


Hide 42311N 4.REMOVE REAR AXLE SHAFT NUT RH (for 4WD/AWD)

HINT:

Use the same procedure described for the LH side.


Hide 89516D 5.DISCONNECT SKID CONTROL SENSOR WIRE LH (for 2WD)

Hide 89516C 6.DISCONNECT SKID CONTROL SENSOR WIRE RH (for 2WD)

HINT:

Use the same procedure described for the LH side.


Hide 7.DISCONNECT REAR SPEED SENSOR LH (for 4WD/AWD)

Hide 8.DISCONNECT REAR SPEED SENSOR RH (for 4WD/AWD)

HINT:

Use the same procedure described for the LH side.


Hide 46430 9.DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 46420 10.DISCONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 11.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 12.DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42431 13.REMOVE REAR DISC

Hide 14.REMOVE PARKING BRAKE ASSEMBLY

Hide 42450B 15.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)

Hide 42450A 16.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH (for 2WD)

HINT:

Use the same procedure described for the LH side.


Hide 42440 17.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD/AWD)

Hide 42410 18.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD/AWD)

HINT:

Use the same procedure described for the LH side.


Hide 52296 19.REMOVE REAR SUSPENSION MEMBER BRACE LH

Hide 52295 20.REMOVE REAR SUSPENSION MEMBER BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 48840A 21.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 22.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48812 23.REMOVE REAR STABILIZER BAR

Hide 48720A 24.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 25.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48710B 26.DISCONNECT REAR TRAILING ARM ASSEMBLY LH

C156413

a.

Remove the 2 bolts and disconnect the rear trailing arm.


Hide 48710B 27.DISCONNECT REAR TRAILING ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48740F 28.LOOSEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 29.LOOSEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42305 30.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH

C156415

a.

Remove the bolt and nut, disconnect the rear upper control arm and remove the rear axle carrier.

NOTICE:

Since a stopper nut is used, loosen the bolt.



Hide 42304 31.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48540 32.REMOVE REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 33.REMOVE REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48231B 34.REMOVE REAR COIL SPRING LH

Hide 48231A 35.REMOVE REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 48259A 36.REMOVE REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 37.REMOVE REAR UPPER COIL SPRING INSULATOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48258C 38.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 39.REMOVE REAR LOWER COIL SPRING INSULATOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48740F 40.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 41.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48790 42.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

C172697

a.

Remove the bolt, nut and upper control arm from the rear suspension member.


Hide 48770A 43.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 37100 44.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 41110 45.REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (for 4WD/AWD)

Hide 51206A 46.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C266838C01
1.229,0.531 1.01,0.531 false 1.01,0.531 1.01,0.885 true 2.469,0.885 2.469,0.542 true 2.469,0.531 2.219,0.531 false 2.583,1.927 2.354,1.927 true 2.354,1.927 2.354,1.76 true 1.063,1.75 1.063,1.917 true 1.063,1.917 0.854,1.917 true 1.26,0.448 1.646,0.667 0.385,0.219 10 *a 2.073,0.438 2.458,0.656 0.385,0.219 10 *a 0.688,1.823 1.073,2.042 0.385,0.219 10 *a 2.635,1.844 3.021,2.063 0.385,0.219 10 *a
*a Attachment Placement Positions


Place wooden blocks or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the suspension member.

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the rear suspension member sub-assembly is level.

·

As the rear suspension member sub-assembly is very heavy, be sure to support it securely.




b.
C266837

Remove the 2 bolts, 2 nuts, 2 rear upper body mounting cushions and rear suspension member sub-assembly.


Hide 41651 47.REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for 4WD/AWD)