Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0050250 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

This circuit sends a signal to the ECM depending on the cruise control switch condition. The battery supplies positive (+) battery voltage to the circuit control switch. Then terminal CCS of the ECM receives the voltage according to the switch condition.

WIRING DIAGRAM

E270490E01
6.448,5.188 6.906,5.385 0.458,0.198 10 false ECM 0.99,3.99 4.198,4.188 3.208,0.198 10 false Cruise Control Switch 3.646,3.823 4.521,4.333 0.875,0.51 10 false Cruise Control Switch Wire 4.656,3.813 5.542,4.552 0.885,0.74 10 false Spiral Cable Sub-assembly 0.115,4.552 6.208,4.729 6.094,0.177 10 false *1: for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF 0.125,4.979 3.188,5.177 3.063,0.198 10 false *2: for 2AR-FE 0.115,5.406 3.177,5.604 3.063,0.198 10 false *3: for 3ZR-FAE, 3ZR-FE 5.229,0.844 5.688,1.042 0.458,0.198 10 false A61 5.26,1.073 5.573,1.271 0.313,0.198 10 false *1 5.979,0.844 6.438,1.042 0.458,0.198 10 false A62 5.594,0.844 6.052,1.042 0.458,0.198 10 false A62 5.615,1.063 5.927,1.26 0.313,0.198 10 false *2 6,1.063 6.313,1.26 0.313,0.198 10 false *3 5.281,0.615 5.594,0.813 0.313,0.198 10 false 23 5.635,0.615 5.948,0.813 0.313,0.198 10 false 40 6.021,0.615 6.333,0.813 0.313,0.198 10 false 60 6.333,0.844 6.792,1.042 0.458,0.198 10 false CCS 4.896,3.427 5.354,3.625 0.458,0.198 10 false ECC 4.896,2.5 5.354,2.698 0.458,0.198 10 false CCS 0.542,2.833 1.458,3.031 0.917,0.198 10 false CANCEL 1.021,3.802 1.177,4 0.156,0.198 10 false A 1.313,2.833 2.083,3.031 0.771,0.198 10 false -SET 2.073,2.854 2.844,3.052 0.771,0.198 10 false +RES 2.885,2.854 3.802,3.052 0.917,0.198 10 false ON-OFF 5.427,2.406 5.74,2.604 0.313,0.198 10 false G8 5.417,3.302 5.729,3.5 0.313,0.198 10 false G8 5.448,2.135 5.76,2.333 0.313,0.198 10 false 1 5.469,3.052 5.781,3.25 0.313,0.198 10 false 2 4.427,2.385 4.74,2.583 0.313,0.198 10 false z4 4.448,3.292 4.76,3.49 0.313,0.198 10 false z4 4.469,3.063 4.781,3.26 0.313,0.198 10 false 4 4.448,2.188 4.76,2.385 0.313,0.198 10 false 3 3.521,2.281 3.833,2.479 0.313,0.198 10 false 3 3.531,3.198 3.844,3.396 0.313,0.198 10 false 1

PROCEDURE

1.READ VALUE USING GTS
a.

Check the Data List for proper functioning of the cruise control switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control switch signal (Main CPU) ON or OFF ON: Cruise control switch is on
OFF: Cruise control switch is off
-
Cancel Switch Switch CANCEL switch signal ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 237 16,23,22,21
OK:

When the cruise control switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL SWITCH
2.INSPECT CRUISE CONTROL SWITCH
a.

b.

Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
E178683C04
0.292,0.729 0.729,1.042 0.438,0.313 0.24,2.385 0.677,2.698 0.438,0.313 1.656,1.542 1.281,1.094 true 0.656,1.542 1.073,1.125 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 0.24,1.969 0.552,2.167 0.313,0.198 10 false *b 0.417,2.458 0.573,2.656 0.156,0.198 10 false A 0.438,0.823 0.75,1.021 0.313,0.198 10 false z4 1.573,1.583 2.031,1.781 0.458,0.198 10 false ECC 0.49,1.552 0.948,1.75 0.458,0.198 10 false CCS
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Switch)


Disconnect the z4 spiral cable sub-assembly connector.


b.

Disconnect the A cruise control switch wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-3 (CCS) - A-3 Always Below 1 Ω
z4-4 (ECC) - A-1 Always Below 1 Ω
z4-3 (CCS) or A-3 - Body ground Always 10 kΩ or higher
z4-4 (ECC) or A-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>REMOVAL

w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL


b.

Inspect the spiral cable sub-assembly.

w/o Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Single Type)>INSPECTION

w/ Occupant Classification System: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

for 1AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A61 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A61-23 (CCS) Always Below 1 Ω
G8-2 (ECC) - Body ground Always Below 1 Ω
G8-1 (CCS) or A61-23 (CCS) - Body ground Always 10 kΩ or higher




b.

for 2AR-FE

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A62-40 (CCS) Always Below 1 Ω
G8-2 (ECC) - Body ground Always Below 1 Ω
G8-1 (CCS) or A62-40 (CCS) - Body ground Always 10 kΩ or higher




c.

for 3ZR-FAE, 3ZR-FE

i.

Disconnect the G8 spiral cable sub-assembly connector.


ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-1 (CCS) - A62-60 (CCS) Always Below 1 Ω
G8-2 (ECC) - Body ground Always Below 1 Ω
G8-1 (CCS) or A62-60 (CCS) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR