A fuel pressure sensor mounted on the common rail converts the fuel pressure inside the common rail into an electric signal, and outputs it to the ECM. The ECM controls the supply pump in order to maintain the fuel pressure inside the common rail at a target pressure calculated by the ECM.
Refer to System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>SYSTEM DESCRIPTION).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0093 | Fuel System Leak Detected - Large Leak | Fuel pressure drop before and after fuel injection is larger than the threshold a certain number of times (0.2 seconds or more).
(1 trip detection logic) |
·
Fuel line between supply pump assembly and common rail assembly ·
Fuel line between common rail assembly and injector assembly ·
Supply pump assembly ·
Pressure discharge valve (built into common rail assembly) ·
Fuel pressure sensor (built into common rail assembly) ·
Injector assembly ·
Crankshaft position sensor ·
Fuel filter assembly ·
Open or short in injector driver (EDU) circuit (P0201, P0202, P0203, P0204 and/or P062D set simultaneously) ·
Open or short in injector assembly circuit (P0201, P0202, P0203, P0204 and/or P062D set simultaneously) ·
Injector driver (EDU) (P0201, P0202, P0203, P0204 and/or P062D set simultaneously) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0093 | ·
Fuel Press ·
Target Common Rail Pressure |
For more information on the common rail system, refer to System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>SYSTEM DESCRIPTION).
If DTC P0093 is present, refer to the Diagnostic Trouble Code Chart (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DIAGNOSTIC TROUBLE CODE CHART).
When DTC P0093 is set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.
| Engine Speed | Fuel Pressure |
|---|---|
| Idling | Approximately 27000 to 45000 kPa |
| 3000 rpm (No engine load) | Approximately 45000 to 78000 kPa |
When there is an operating problem with the fuel supply pump (Fuel Press is less than Target Common Rail Pressure), the values of Injection Pressure Correction and Target Pump SCV Current will increase.
This DTC indicates that fuel leaks exist in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when the fuel is injected.
In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump, common rail, fuel injectors and piping. The ECM adjusts the suction control valve opening angle to obtain the desired fuel pressure.
If this DTC is stored, the ECM enters fail-safe mode. The fail-safe mode suspends both fuel injection and fuel supply pump operation, and then stops the engine. Before stopping the engine, the ECM permits the vehicle to be driven for 60 seconds. The fail-safe mode continues until the ignition switch is turned off.
| Required Sensor | Fuel pressure sensor |
| Frequency of operation | Continuous |
| Duration | 1 second |
| MIL operation | 1 driving cycle |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0093 | After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A) Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B) Repeat procedures (*A) and (*B) 5 times. |
Soon after starting the engine, visually check for fuel leaks in the fuel line.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION) and initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).
After replacing the supply pump assembly, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).
After replacing a fuel injector, the ECM needs registration (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).
Read freeze frame data (multi freeze frame data) using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
*1: Common Rail Pressure suddenly decreases for a moment, and then recovers. This can be seen clearly by comparing it to Target Common Rail Pressure.
*2: Injection Feedback Val #3 is 5.0 mm3/st which is large (the normal value is between -3.0 and 3.0 mm3/st) and indicates that the injector of cylinder 3 may be malfunctioning.
| Data List | Value | Unit |
|---|---|---|
| Engine Speed | 1478 | rpm |
| Fuel Press | 8900 | kPa |
| Target Common Rail Pressure | 65320 | kPa |
| Injection Volume (Point A) | 51.26*1 | mm3/st |
| Injection Volume (Point A`) | 9.76 | mm3/st |
| Accel Position | 63.67 | % |
| Injection Feedback Val #1 | -1.1 | mm3/st |
| Injection Feedback Val #2 | -2.5 | mm3/st |
| Injection Feedback Val #3 | 5.0 | mm3/st |
| Injection Feedback Val #4 | -1.8 | mm3/st |
| MIL | ON | - |
Before starting the engine, visually check for fuel leaks from the supply pump assembly, injector assemblies, common rail assembly and the fuel pipes in high-pressure areas.
No fuel leaks in high-pressure areas.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs and freeze frame data.
| Result | Proceed to |
|---|---|
| Except below | A |
| DTC P0093 and "P0335 and/or P0339" are output | B |
| DTC P0093 and "P0190, P0192 and/or P0193" are output | C |
A
B
C
Check if the fuel level is low.
| Proceed to |
|---|
| The indicator (fuel warning light) is illuminated |
| The indicator (fuel warning light) is not illuminated |
The indicator (fuel warning light) is illuminated
The indicator (fuel warning light) is not illuminated
Add fuel.
| Proceed to |
|---|
| NEXT |
NEXT
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Hand pump pumping speed: Max. 2 strokes/sec.
The hand pump must be pushed with a full stroke during pumping.
When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.
Start the engine.
If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.
Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
Use a fully-charged battery.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Start the engine. (*A)
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak. (*B)
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the Current DTCs.
When no DTCs are output, the air bleeding is completed.
If any DTCs are output, proceed to the next step.
Repeat steps (*A) to (*D).
Clear the DTCs.
Start the engine and warm it up.
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)
Repeat procedures (*E) and (*F) 5 times.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the Current DTCs.
| Proceed to |
|---|
| DTC is output |
| DTC is not output |
DTC is output
DTC is not output
Read the value of Injection Feedback Val #1 to #4 in the Freeze Frame Data recorded in Procedure 2.
| Result | Proceed to |
|---|---|
| Except below | A |
| Injection Feedback Val for at least one cylinder is 5.0 mm3/st in at least 1 set of freeze frame data | B |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
| Tester Display |
|---|
| Fuel Press |
Start the engine.
Read the value of Fuel Press while cranking and idling the engine.
| Result | Proceed to |
|---|---|
| Except below | A |
| The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from off to on. | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
| Tester Display |
|---|
| Injection Feedback Val #1 |
| Injection Feedback Val #2 |
| Injection Feedback Val #3 |
| Injection Feedback Val #4 |
Read the values.
| Tester Display | Engine Condition* | Normal Value |
|---|---|---|
| Injection Feedback Val #1
Injection Feedback Val #2 Injection Feedback Val #3 Injection Feedback Val #4 |
Idling | -3.0 mm3/st to 3.0 mm3/st |
*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or higher and the engine should be idled for 1 minute or more.
| Result | Proceed to |
|---|---|
| Except below | A |
| Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st and engine vibration is abnormally large | B |
When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.
The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.
A
B
Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.
Stop the vehicle and allow the engine to idle.
While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it [A].
Repeat procedure [A] 5 times.
| Result | Proceed to |
|---|---|
| No problems such as sluggishness or variations in the tachometer reading | A |
| Except above | B |
A
B
Replace the fuel filter element assembly.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL FILTER>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Common Rail Pressure |
| Fuel Press |
| Target Pump SCV Current |
Start the engine.
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.
"Target Common Rail Pressure" means target fuel pressure controlled by the ECM.
"Fuel Press" is the actual fuel pressure in common rail assembly.
| Result | Proceed to |
|---|---|
| The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa | A |
| Except above | B |
A
B
Use this Active Test to determine the malfunctioning cylinder.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder Fuel Cut / #1 to #4.
If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.
If the cylinder being tested is normal, there will be a significant change in idle speed when the injection assembly is stopped for that cylinder.
| Tester Display |
|---|
| Control the Select Cylinder Fuel Cut |
| Proceed to |
|---|
| NEXT |
NEXT
Remove the glow plug assembly for all the cylinders.
Click hereEngine / Hybrid System>2AD-FTV STARTING>GLOW PLUG>REMOVAL
Visually check if there is fuel on the glow plug assemblies.
If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.
After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.
If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assembly of the malfunctioning cylinder.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
Perform the pilot quantity learning.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the value while cranking and idling the engine.
| Tester Display | Engine Condition | Specified Condition |
|---|---|---|
| Engine Speed | Cranking | 50 to 400 rpm |
| Idling with warm engine | 750 to 850 rpm |
The value is the same as the actual engine speed and is displayed with no interruption on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DTC CHECK / CLEAR
| *1 | Engine | *2 | Engine Wire |
| *3 | Common Rail Assembly
(Fuel Pressure Sensor) |
*4 | Wire to Wire |
| *5 | ECM | - | - |
| *a | Vibration Method (Reference) | - | - |
Check if the MIL illuminates up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
The MIL does not come on.
| Proceed to |
|---|
| MIL does not come on |
| MIL comes on |
MIL does not come on
MIL comes on
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Temperature.
| Tester Display |
|---|
| Fuel Temperature |
Read the value.
The value is almost the same as the actual fuel temperature.
When the engine is stopped and left overnight, the fuel temperature becomes the same as the atmospheric temperature.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for intermittent problems.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>CHECK FOR INTERMITTENT PROBLEMS
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel temperature sensor.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL TEMPERATURE SENSOR>REMOVAL
Before replacing the fuel temperature sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and warm it up (engine coolant temperature is 75°C (167°F) or higher).
Confirm that the shift lever is in neutral and securely apply the parking brake.
Fully depress the accelerator pedal for 5 seconds and then release it [A].
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm [B].
Repeat the above procedures [A] and [B] 5 times.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector (ECM - fuel pressure sensor).
| Proceed to |
|---|
| NEXT |
NEXT
If the MIL has illuminated before in the past, clear the DTC using the GTS before performing this inspection.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DTC CHECK / CLEAR
| *1 | Engine | *2 | Engine Wire |
| *3 | Common Rail Assembly
(Fuel Pressure Sensor) |
*4 | Wire to Wire |
| *5 | ECM | - | - |
| *a | Vibration Method (Reference) | - | - |
Check if the MIL illuminates up when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
The MIL does not come on.
| Proceed to |
|---|
| MIL does not come on |
| MIL comes on |
MIL comes on
MIL does not come on
Replace the common rail assembly.
Click hereEngine / Hybrid System>2AD-FTV FUEL>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL
Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT