Home › Drivetrain › GF1A TRANSFER / 4WD / AWD › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › 2015.04–2015.10
RM3090E _52 Drivetrain _008760 GF1A TRANSFER / 4WD / AWD _0048749 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM J

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

for Segment Display Type:

Connecting terminals TC and CG of the DLC3 causes the 4WD ECU assembly to display 2-digit DTCs by flashing the 4WD/AWD warning light.

for Dot Display Type:

Connecting terminals TC and CG of the DLC3 causes the 4WD ECU assembly to display a DTC on the multi-information display.

HINT:

When each warning light remains blinking, a short to ground in the wiring of terminal TC of the DLC3 or an internal short to ground in each ECU is suspected.


WIRING DIAGRAM

C256466E25
5.396,1.427 6.76,1.646 1.365,0.219 10 false 4WD ECU Assembly 3.698,2.698 3.979,2.844 0.281,0.146 10 false G14 3.708,2.906 4.115,3.052 0.406,0.146 10 false DLC3 3.615,2.125 3.865,2.281 0.25,0.156 10 false CG 3.615,1.698 3.844,1.854 0.229,0.156 10 false TC 0.542,2.948 0.979,3.094 0.438,0.146 10 false ECM 0.906,1.708 1.135,1.865 0.229,0.156 10 false TC 1.021,4.208 2.99,4.385 1.969,0.177 10 false : CAN Communication Line 1.188,1.583 2.354,1.781 1.167,0.198 10 false 23*1, 33*2, 26*2 3.354,1.604 3.552,1.802 0.198,0.198 10 false 13 3.438,2.031 3.594,2.229 0.156,0.198 10 false 4 0.521,2.74 2.354,2.938 1.833,0.198 10 false A62*1, *2, A61*3 3.479,3.51 5.635,3.698 2.156,0.188 10 false *1: for 2AR-FE, 3ZR-FE 3.479,4.271 5.802,4.469 2.323,0.198 10 false *3: for 2AD-FHV, 2AD-FTV, 1AD-FTV 3.479,3.885 5.771,4.083 2.292,0.198 10 false *2: for 3ZR-FAE

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check if the CAN communication system DTC is output.

for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM

for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM

Result:
Proceed to
CAN communication system DTC is not output
CAN communication system DTC is output (for LHD)
CAN communication system DTC is output (for RHD)




CAN communication system DTC is not output

2.INSPECT DLC3

CAN communication system DTC is output (for LHD)

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

CAN communication system DTC is output (for RHD)

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.INSPECT DLC3
a.
C146309C94
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G14-13 (TC) - G14-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

3.CHECK HARNESS AND CONNECTOR (TC OF DLC3 - TC OF ECM AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (TC OF DLC3 - TC OF ECM AND BODY GROUND)
a.

Turn the ignition switch off.


b.

for 2AR-FE, 3ZR-FAE, 3ZR-FE:

Disconnect the A62 ECM connector.

for 2AD-FHV, 2AD-FTV, 1AD-FTV:

Disconnect the A61 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2AR-FE, 3ZR-FE
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-23 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher

for 2AD-FHV, 2AD-FTV, 1AD-FTV
Tester Connection Condition Specified Condition
G14-13 (TC) - A61-26 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher

for 3ZR-FAE
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-33 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)
a.
C166029C51
0.135,1.01 0.563,1.313 0.427,0.302 1.594,0.906 1.854,0.313 true 1.823,0.135 2.188,0.313 0.365,0.177 10 CG 0.125,0.073 0.344,0.25 0.219,0.177 10 *a 0.208,1.073 0.531,1.25 0.323,0.177 10 G14
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-4 (CG) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
C146309C94
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a Front view of DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Result:
Proceed to
Malfunction indicator lamp is blinking (for 2AD-FHV)
Malfunction indicator lamp is blinking (for 2AD-FTV)
Malfunction indicator lamp is blinking (for 2AR-FE)
Malfunction indicator lamp is blinking (for 3ZR-FAE)
Malfunction indicator lamp is blinking (for 3ZR-FE)
Malfunction indicator lamp is blinking (for 1AD-FTV)
Malfunction indicator lamp is not blinking



Malfunction indicator lamp is blinking (for 2AD-FHV)

Malfunction indicator lamp is blinking (for 2AD-FTV)

Malfunction indicator lamp is blinking (for 2AR-FE)

Malfunction indicator lamp is blinking (for 3ZR-FAE)

Malfunction indicator lamp is blinking (for 3ZR-FE)

Malfunction indicator lamp is blinking (for 1AD-FTV)

Malfunction indicator lamp is not blinking