Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A  


DESCRIPTION

The ECM uses 2 sensors to detect the engine speed and the position of the crankshaft and camshaft. The crankshaft position sensor detects the engine speed and top dead center position of the crankshaft. The camshaft position sensor determines when the cylinder is at the top dead center of the compression or exhaust stroke.

The exhaust gas value worsens due to an angular error between the crankshaft and camshaft. The ECM stores DTC P0016 if the angular error between the crankshaft and camshaft exceeds the threshold.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A Phase deviation in crankshaft and camshaft position sensor signals.
(3 trip detection logic)
·

Camshaft and camshaft timing sprocket installation condition

·

Camshaft position sensor installation condition

·

Valve timing

·

Looseness in timing chain

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT CAMSHAFT AND CAMSHAFT TIMING SPROCKET INSTALLATION CONDITION
a.
A318369

Remove the cylinder head cover sub-assembly so that the camshaft timing sprocket is visible.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Check the camshaft and camshaft timing sprocket installation condition.

OK:

Camshaft and camshaft timing sprocket securely installed without looseness.


HINT:

The holes for the bolts which connect the camshaft timing sprocket to the camshaft are long. If there is looseness, the parts can slide and become misaligned.



Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

8.CHECK CAMSHAFT AND CAMSHAFT TIMING SPROCKET INSTALLATION CONDITION
2.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.

Check the camshaft position sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)

NG

7.SECURELY REINSTALL SENSOR
3.CHECK VALVE TIMING (CHECK FOR LOOSE OR JUMPED TEETH ON TIMING CHAIN)
a.

Remove the cylinder head cover sub-assembly so that the camshaft timing sprocket is visible.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Rotate the crankshaft, and then using SST, secure the crankshaft at compression top dead center.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>INSTALLATION


c.

Check the camshaft alignment marks.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

OK:

The valve timing is correctly aligned.



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE ENGINE MECHANICAL SYSTEM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE ENGINE MECHANICAL SYSTEM
a.

Repair or replace for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>INSTALLATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.SECURELY REINSTALL SENSOR

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK CAMSHAFT AND CAMSHAFT TIMING SPROCKET INSTALLATION CONDITION
a.

Check the camshaft and camshaft timing sprocket installation condition and perform reinstallation if necessary.

HINT:

The camshaft and camshaft timing sprocket installation condition can be checked using SST.

Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>CAMSHAFT>REMOVAL



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED