Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0090  Open Load of Pressure Control Valve Output  P0091  Short Circuit to Ground of Pressure Control Valve Output  P0092  Short Circuit to Battery of Pressure Control Valve Output  


DESCRIPTION

The pressure discharge valve assembly is installed to the common rail assembly.

The ECM controls the pressure discharge valve assembly based on the signals from the fuel pressure sensor and maintains the fuel pressure inside the common rail assembly at the target set pressure.

HINT:

When the pressure discharge valve assembly is not supplied with current, the pressure discharge valve assembly is opened. For more information on the fuel system, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


A342523E02
2.198,0.917 2.51,0.198 2.51,0.198 2.323,0.198 false 1.667,2.073 1.417,2.073 1.417,2.073 1.167,1.573 false 5.938,2.073 5.802,2.073 5.802,2.073 5.625,1.583 false 5.031,2.042 4.865,2.042 4.865,2.042 4.76,1.531 false 5.833,1.5 5.667,0.5 5.667,0.5 5.5,0.5 false 4.76,1.031 4.594,0.792 false 1.458,0.75 1.208,0.583 false 3.948,1.781 4.094,1.563 false 0.073,0.094 2.375,0.469 2.302,0.375 10 false Pressure Discharge Valve Assembly 0.396,0.49 2.052,0.708 1.656,0.219 10 false Fuel (Return) 1.729,1.99 3.385,2.208 1.656,0.219 10 false Common Rail Assembly 5.094,1.958 5.875,2.198 0.781,0.24 10 false Ball Valve 6.021,2.01 6.615,2.448 0.594,0.438 10 false Pressure Pin 4.521,0.417 5.646,0.656 1.125,0.24 10 false Opening Spring 3.75,0.677 5.406,0.896 1.656,0.219 10 false Fuel (Return) 3.677,1.823 4.51,2.25 0.833,0.427 10 false Fuel (from Common-rail)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0090 Open Load of Pressure Control Valve Output Open in pressure discharge valve circuit for 0.1 seconds.
(3 trip detection logic)
·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve assembly

·

ECM


Does not come on DTC stored
P0091 Short Circuit to Ground of Pressure Control Valve Output Short to ground in pressure discharge valve circuit for 0.1 seconds or more for 0.05 seconds or more.
(3 trip detection logic)
·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve assembly

·

ECM


Does not come on DTC stored
P0092 Short Circuit to Battery of Pressure Control Valve Output Short to power source in pressure discharge valve circuit for 0.1 seconds or more
(3 trip detection logic)
·

Open or short in pressure discharge valve circuit

·

Pressure discharge valve assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P0090
P0091
P0092
·

Rail Pressure Control Valve - Current Value from Rail Pressure Valve Control

·

Target Common Rail Pressure

·

Common Rail Pressure



WIRING DIAGRAM

A351166E09
0.604,2.073 1.229,2.458 0.625,0.385 10 false EFI MAIN NO. 1 1.323,0.917 1.708,1.198 0.385,0.281 10 false 5 2.083,0.917 2.469,1.198 0.385,0.281 10 false 3 2.083,1.427 2.469,1.708 0.385,0.281 10 false 1 1.323,1.427 1.708,1.708 0.385,0.281 10 false 2 0.615,3.167 1.844,3.365 1.229,0.198 10 false FL MAIN 0.75,3.75 1.979,3.948 1.229,0.198 10 false Battery 6.188,3.844 6.792,4.083 0.604,0.24 10 false ECM 5.771,2.021 6.375,2.26 0.604,0.24 10 false MREL 5.365,2.135 5.969,2.375 0.604,0.24 10 false A62 5.729,1.031 6.333,1.271 0.604,0.24 10 false PRV 5.323,1.031 5.927,1.271 0.604,0.24 10 false B112 5.406,0.854 6.01,1.094 0.604,0.24 10 false 60 5.448,1.948 6.052,2.188 0.604,0.24 10 false 9 3.542,1.375 4.146,1.615 0.604,0.24 10 false B128 3.552,1.521 5.271,2.115 1.719,0.594 10 false Pressure Discharge Valve 2.677,1.188 3.438,1.427 0.76,0.24 10 false EFI NO. 1 3.74,0.927 4.344,1.167 0.604,0.24 10 false 1 4.708,0.927 5.313,1.167 0.604,0.24 10 false 2 3.906,0.927 4.51,1.167 0.604,0.24 10 false SPV+ 4.302,0.927 4.906,1.167 0.604,0.24 10 false SPV- 1.448,1.667 2.115,2.073 0.667,0.406 10 false EFI MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the pressure discharge valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT PRESSURE DISCHARGE VALVE ASSEMBLY
a.

Inspect the pressure discharge valve assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE DISCHARGE VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)

NG

8.REPLACE PRESSURE DISCHARGE VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE - ECM)
a.

Disconnect the pressure discharge valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B128-2 (SPV-) - B112-60 (PRV) Always Below 1 Ω
B128-2 (SPV-) or B112-60 (PRV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351161C03
0.302,0.906 0.719,1.167 0.417,0.26 0.875,1.802 1.521,1.26 false 0.344,0.198 0.656,0.354 0.313,0.156 10 false *a 0.344,0.958 0.76,1.219 0.417,0.26 10 false B128 0.427,1.781 0.844,2.042 0.417,0.26 10 false SPV+
*a Front view of wire harness connector
(to Pressure Discharge Valve Assembly)


a.

Disconnect the pressure discharge valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B128-1 (SPV+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (PRESSURE DISCHARGE VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the pressure discharge valve assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B128-1 (SPV+) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B128-1 (SPV+) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM POWER SOURCE CIRCUIT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE PRESSURE DISCHARGE VALVE ASSEMBLY
a.

Replace the pressure discharge valve assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE DISCHARGE VALVE>REMOVAL


b.

Perform fuel PCV compensation value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END