Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P00BC  Mass or Volume Air Flow "A" Circuit Range/Performance - Air Flow Too Low  


DESCRIPTION

HINT:

For more information on the EGR control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P00BC Mass or Volume Air Flow "A" Circuit Range/Performance - Air Flow Too Low Either condition is met (3 trip detection logic):
·

Difference exists between estimated MAF and actual MAF for 5 seconds.

·

When boost pressure control errors are detected on both high pressure and low pressure sides for 5 seconds.


·

Intake system air leak

·

EGR valve assembly

·

EGR cooler assembly

·

Turbo pressure sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P00BC
·

Target EGR Position

·

Actual EGR Valve Pos



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK INTAKE SYSTEM
a.

Check for air leaks in the intake system from the mass air flow meter sub-assembly to the turbocharger sub-assembly.


Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF EGR-VALVE)

NG

10.REPAIR OR REPLACE INTAKE SYSTEM
2.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF EGR-VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of EGR-Valve / Data List / Target EGR Position and Actual EGR Valve Pos.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of EGR-Valve
Data List Display
Target EGR Position
Actual EGR Valve Pos
50004 371 2 18,24

e.

Perform the following steps 1 to 4.


f.

Step 1

i.

Perform Actuator Test of EGR-Valve with control value of 0% (opening ratio in %).


ii.

Monitor the difference of the control value and EGR valve Actuator Position value (0 +/- 3%). EGR valve must operate within 1 second.



g.

Step 2

i.

Wait for 2 seconds or more.



h.

Step 3

i.

Perform Actuator Test of EGR-Valve with control value of 94% (opening ratio in %).


ii.

Monitor the difference of the control value and EGR valve Actuator Position value (0 +/- 3%). EGR valve must operate within 1 second.



i.

Step 4

i.

Wait for 2 seconds or more.



j.

Perform the above steps 1 to 4 and check that the part operates as specified.

OK:

Part operates as specified.


HINT:
·

Make sure that the EGR valve is not stuck open due to carbon jamming or an operation malfunction.

·

If DTCs P00BC, P042F or P1268 is output, there may be a malfunction in the EGR system.




Result:
Proceed to
OK
NG



OK

3.CHECK EGR COOLER ASSEMBLY

NG

8.REPLACE EGR VALVE ASSEMBLY
3.CHECK EGR COOLER ASSEMBLY
a.

Check that the airflow is not slowed by soot deposits in the EGR cooler assembly.

OK:

Airflow is not slowed by soot deposits.



Result:
Proceed to
OK
NG



OK

4.CHECK TURBO PRESSURE SENSOR ASSEMBLY

NG

7.CLEAN EGR COOLER ASSEMBLY
4.CHECK TURBO PRESSURE SENSOR ASSEMBLY
a.

Check for DTCs related to the turbo pressure sensor assembly.


Result:
Proceed to
OK
NG



OK

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P00BC)

NG

6.REPAIR OR REPLACE TURBO PRESSURE SENSOR ASSEMBLY
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P00BC)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P00BC B




A

END

B

11.REPLACE ECM
6.REPAIR OR REPLACE TURBO PRESSURE SENSOR ASSEMBLY
a.

Repair or replace turbo pressure sensor assembly or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

HINT:

When the turbo pressure sensor assembly is replaced, perform initialization.



Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CLEAN EGR COOLER ASSEMBLY
a.

Clean the EGR cooler assembly.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Perform EGR learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P00BC)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P00BC)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P00BC B




A

END

B

11.REPLACE ECM
10.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning parts of the intake system.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END