Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0102  Mass or Volume Air Flow Sensor "A" Circuit Low  P0103  Mass or Volume Air Flow Sensor "A" Circuit High  


DESCRIPTION

The hot film air mass meter sub-assembly is attached to the air intake hose to the intake silencer.

The hot film air mass meter sub-assembly is a combined sensor. The hot film air mass meter sub-assembly detects the actual amount of air independently from the air pressure. In conjunction with other sensors, the ECM calculates the amount of fuel to be injected. An intake air temperature sensor is integrated into the hot film air mass meter. This sensor measures the temperature of the intake air before the exhaust turbocharger.

The flow path employed in the hot film air mass meter sub-assembly is divided into two paths. Centrifugal force separates the clean air from moisture and particulates. In one flow path the clean air destined for measurement is conducted to the monitoring element. The other flow path discharges moisture and particulates.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass or Volume Air Flow Sensor "A" Circuit Low Generated pulse period is 71 μsec. or less (MAF value is extremely high).
(3 trip detection logic)
·

Open or short in Mass Air Flow (MAF) meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored
P0103 Mass or Volume Air Flow Sensor "A" Circuit High Generated pulse period is 833 μsec. or more (MAF value is extremely low).
(3 trip detection logic)
·

Open or short in Mass Air Flow (MAF) meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0102
P0103
MAF

WIRING DIAGRAM

A351168E03
0.427,0.865 1.042,1.271 0.615,0.406 10 false EFI MAIN NO. 1 1.625,1.49 2.24,1.854 0.615,0.365 10 false EFI MAIN NO. 1 0.417,2.958 1.646,3.156 1.229,0.198 10 false FL MAIN 0.635,3.792 1.865,3.99 1.229,0.198 10 false Battery 2.521,0.771 3.75,0.969 1.229,0.198 10 false EFI NO. 2 3.344,1.833 5.594,2.146 2.25,0.313 10 false Mass Air Flow Meter Sub-assembly 3.354,1.677 4.906,1.875 1.552,0.198 10 false B113 4.031,0.646 4.656,0.844 0.625,0.198 10 false +B 4.75,0.625 5.375,0.823 0.625,0.198 10 false VG 4.656,1.063 5.281,1.26 0.625,0.198 10 false VGR 4.667,1.51 5.292,1.708 0.625,0.198 10 false E2G 5.479,0.615 6.104,0.813 0.625,0.198 10 false B112 5.479,1.083 6.104,1.281 0.625,0.198 10 false B112 5.469,1.531 6.094,1.729 0.625,0.198 10 false B112 5.51,2.344 6.135,2.542 0.625,0.198 10 false A62 5.51,2.979 6.135,3.177 0.625,0.198 10 false A62 5.885,2.969 6.51,3.167 0.625,0.198 10 false E1 5.885,2.333 6.51,2.531 0.625,0.198 10 false MREL 5.875,1.542 6.5,1.74 0.625,0.198 10 false EVG 5.896,1.073 6.521,1.271 0.625,0.198 10 false VGR 5.906,0.604 6.531,0.802 0.625,0.198 10 false VG 3.823,0.531 4.448,0.729 0.625,0.198 10 false 1 2.25,1.063 2.542,1.302 0.292,0.24 10 false 1 5.031,0.49 5.25,0.698 0.219,0.208 10 false 5 5.031,0.958 5.25,1.167 0.219,0.208 10 false 4 5.021,1.417 5.24,1.625 0.219,0.208 10 false 2 5.563,0.417 5.781,0.625 0.219,0.208 10 false 97 5.563,0.896 5.781,1.104 0.219,0.208 10 false 98 5.521,1.333 5.813,1.583 0.292,0.25 10 false 129 5.594,2.135 5.885,2.385 0.292,0.25 10 false 9 5.604,2.792 5.896,3.042 0.292,0.25 10 false 4 1.51,0.51 1.729,0.719 0.219,0.208 10 false 5 1.51,1.073 1.729,1.281 0.219,0.208 10 false 2 2.25,0.51 2.469,0.719 0.219,0.208 10 false 3 6.302,3.604 6.927,3.802 0.625,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the mass air flow meter sub-assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351157C04
0.188,1.021 0.604,1.313 0.417,0.292 2.333,1.281 2.625,1.552 false 0.417,0.302 0.729,0.458 0.313,0.156 10 false *a 0.24,1.094 0.667,1.344 0.427,0.25 10 false B113 2.698,1.51 3.125,1.76 0.427,0.25 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B113-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI MAIN NO. 1 RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B113-5 (VG) - B112-97 (VG) Always Below 1 Ω
B113-4 (VGR) - B112-98 (VGR) Always Below 1 Ω
B113-2 (E2G) - B112-129 (EVG) Always Below 1 Ω
B113-5 (VG) or B112-97 (VG) - Body ground Always 10 kΩ or higher
B113-4 (VGR) or B112-98 (VGR) - Body ground Always 10 kΩ or higher
B113-2 (E2G) or B112-129 (EVG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL


b.

Perform the air flow meter learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0102 AND/OR P0103)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0102 AND/OR P0103)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
DTC P0102 and/or P0103 A
No DTC output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B113-1 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B113-1 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK ECM POWER SOURCE CIRCUIT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END