Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0135  O2 Sensor Heater Circuit Bank 1 Sensor 1  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0135 O2 Sensor Heater Circuit Bank 1 Sensor 1 The temperature of the air fuel ratio sensor (for sensor 1) is equal to or less than the threshold
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 1) circuit

·

Air fuel ratio sensor (for sensor 1)

·

Open or short in air fuel ratio sensor (for sensor 1) heater circuit

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0135)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P0135 A
DTC P0135 and other DTCs B


HINT:

If any DTCs other than P0135 are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR ((FOR SENSOR 1) (HEATER RESISTANCE))

B

2.INSPECT AIR FUEL RATIO SENSOR ((FOR SENSOR 1) (HEATER RESISTANCE))
a.

Inspect the air fuel ratio sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

11.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
A351154C13
0.281,1.083 0.729,1.333 0.448,0.25 1.063,1.844 1.688,1.177 true 0.354,1.135 0.74,1.385 0.385,0.25 10 false B107 0.906,1.875 1.25,2.104 0.344,0.229 10 false +B 0.406,0.281 0.75,0.51 0.344,0.229 10 false *a
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor (for Sensor 1))


a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B107-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - EFI MAIN NO. 1 RELAY)
4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B107-1 (AF1+) - B112-127 (AF1+) Always Below 1 Ω
B107-2 (AF1-) - B112-126 (AF1-) Always Below 1 Ω
B107-3 (HAF1) - B112-46 (HAF1) Always Below 1 Ω
B107-5 (TR1) - B112-128 (TR1) Always Below 1 Ω
B107-6 (RE1) - B112-125 (RE1) Always Below 1 Ω
B107-1 (AF1+) or B112-127 (AF1+) - Body ground Always 10 kΩ or higher
B107-2 (AF1-) or B112-126 (AF1-) - Body ground Always 10 kΩ or higher
B107-3 (HAF1) or B112-46 (HAF1) - Body ground Always 10 kΩ or higher
B107-5 (TR1) or B112-128 (TR1) - Body ground Always 10 kΩ or higher
B107-6 (RE1) or B112-125 (RE1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
a.

Replace the air fuel ratio sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0135)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0135)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.


Result:
Result Proceed to
DTC P0135 A
No DTC output B



A

7.REPLACE ECM

B

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 1) - EFI MAIN NO. 1 RELAY)
a.

Disconnect the air fuel ratio sensor (for sensor 1) connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B107-4 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B107-4 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ECM POWER SOURCE CIRCUIT

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 1)
a.

Replace the air fuel ratio sensor (for sensor 1).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END