Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0191  Fuel Rail Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

Refer to DTC P0192.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0192

For information on the fuel system, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0191 Fuel Rail Pressure Sensor "A" Circuit Range/Performance Either condition is met (3 trip detection logic):
·

Fuel pressure sensor feedback value exceeds upper limit for 0.1 seconds.

·

Fuel pressure sensor feedback value falls below lower limit for 0.1 seconds.


·

Open or short in fuel pressure sensor circuit

·

Fuel pressure sensor

·

ECM


Comes on DTC stored

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM and/or injector assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the fuel pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B124-2 (PCR1) - B112-101 (PC) Always Below 1 Ω
B124-3 (VC1) - B112-54 (VCS) Always Below 1 Ω
B124-1 (E1) - B112-102 (E2S) Always Below 1 Ω
B124-2 (PCR1) or B112-101 (PC) - Body ground Always 10 kΩ or higher
B124-3 (VC1) or B112-54 (VCS) - Body ground Always 10 kΩ or higher
B124-1 (E1) or B112-102 (E2S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351160C07
0.24,1.094 0.656,1.354 0.417,0.26 1.083,1.771 1.365,1.281 true 2.396,1.771 2.052,1.281 true 0.271,0.135 0.583,0.333 0.313,0.198 10 false *a 0.979,1.802 1.292,2 0.313,0.198 10 false E1 2.292,1.802 2.604,2 0.313,0.198 10 false VC1 0.292,1.146 0.688,1.344 0.396,0.198 10 false B124
*a Front view of wire harness connector
(to Fuel Pressure Sensor)


a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B124-3 (VC1) - B124-1 (E1) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.REPLACE FUEL PRESSURE SENSOR

NG

5.REPLACE ECM
3.REPLACE FUEL PRESSURE SENSOR
a.

Replace the fuel pressure sensor.

Click hereEngine / Hybrid System>2WW FUEL>FUEL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0191)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.


Result:
Result Proceed to
No DTC output A
DTC P0191 B



A

END

B

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END