Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0201  Cylinder 1 Injector "A" Circuit  P0202  Cylinder 2 Injector "A" Circuit  P0203  Cylinder 3 Injector "A" Circuit  P0204  Cylinder 4 Injector "A" Circuit  P062D  Fuel Injector Driver Circuit Performance Bank 1  


DESCRIPTION

The injector assemblies are installed in the cylinder head and inject fuel into the cylinders based on the signals from the ECM.

HINT:
·

Injector driver is built into the ECM.

·

For more information on the injector assembly and fuel injection control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0201 Cylinder 1 Injector "A" Circuit Open or short in injector circuit (cylinder No. 1) for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in No. 1 injector assembly circuit

·

No. 1 injector assembly

·

ECM


Comes on DTC stored
P0202 Cylinder 2 Injector "A" Circuit Open or short in injector circuit (cylinder No. 2) for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in No. 2 injector assembly circuit

·

No. 2 injector assembly

·

ECM


Comes on DTC stored
P0203 Cylinder 3 Injector "A" Circuit Open or short in injector circuit (cylinder No. 3) for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in No. 3 injector assembly circuit

·

No. 3 injector assembly

·

ECM


Comes on DTC stored
P0204 Cylinder 4 Injector "A" Circuit Open or short in injector circuit (cylinder No. 4) for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in No. 4 injector assembly circuit

·

No. 4 injector assembly

·

ECM


Comes on DTC stored
P062D Fuel Injector Driver Circuit Performance Bank 1 Either condition is met (3 trip detection logic):
·

Short in wire harness of injector circuit

·

ECM internal error


·

Short in injector assembly circuit

·

Injector assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A311428E04
2.198,1.094 2.354,1.292 0.156,0.198 10 false 2 2.198,2.135 2.354,2.333 0.156,0.198 10 false 2 2.208,3.167 2.365,3.365 0.156,0.198 10 false 2 2.208,4.219 2.365,4.417 0.156,0.198 10 false 2 3.25,1.083 3.406,1.281 0.156,0.198 10 false 1 3.25,2.135 3.406,2.333 0.156,0.198 10 false 1 3.24,3.167 3.396,3.365 0.156,0.198 10 false 1 3.25,4.219 3.406,4.417 0.156,0.198 10 false 1 2.365,1.094 2.625,1.292 0.26,0.198 10 false #10 2.354,2.156 2.615,2.354 0.26,0.198 10 false #20 2.365,3.188 2.625,3.385 0.26,0.198 10 false #30 2.354,4.24 2.615,4.438 0.26,0.198 10 false #40 3.021,4.229 3.281,4.427 0.26,0.198 10 false #4 3.01,3.177 3.271,3.375 0.26,0.198 10 false #3 3.01,2.146 3.271,2.344 0.26,0.198 10 false #2 3,1.094 3.26,1.292 0.26,0.198 10 false #1 1.948,1.521 2.208,1.719 0.26,0.198 10 false I1 2.208,1.521 3.802,1.771 1.594,0.25 10 false No. 1 Injector Assembly 1.938,2.531 2.198,2.729 0.26,0.198 10 false I2 2.219,2.531 3.813,2.781 1.594,0.25 10 false No. 2 Injector Assembly 1.958,3.563 2.219,3.76 0.26,0.198 10 false I3 2.208,3.563 3.802,3.813 1.594,0.25 10 false No. 3 Injector Assembly 2.229,4.635 3.823,4.885 1.594,0.25 10 false No. 4 Injector Assembly 1.958,4.635 2.219,4.833 0.26,0.198 10 false I4 5.625,0.708 5.885,0.906 0.26,0.198 10 false 29 5.635,2.135 5.896,2.333 0.26,0.198 10 false 58 5.625,1.729 5.885,1.927 0.26,0.198 10 false 28 5.625,1.094 5.885,1.292 0.26,0.198 10 false 59 5.625,2.781 5.885,2.979 0.26,0.198 10 false 27 5.625,3.823 5.885,4.021 0.26,0.198 10 false 26 5.625,3.188 5.885,3.385 0.26,0.198 10 false 57 5.625,4.219 5.885,4.417 0.26,0.198 10 false 56 5.885,0.813 6.292,1.031 0.406,0.219 10 false IJ1+ 5.885,1.188 6.292,1.406 0.406,0.219 10 false IJ1- 5.885,1.844 6.292,2.063 0.406,0.219 10 false IJ2+ 5.885,2.24 6.292,2.458 0.406,0.219 10 false IJ2- 5.875,2.875 6.281,3.094 0.406,0.219 10 false IJ3+ 5.885,3.281 6.292,3.5 0.406,0.219 10 false IJ3- 5.875,4.323 6.281,4.542 0.406,0.219 10 false IJ4- 5.875,3.917 6.281,4.135 0.406,0.219 10 false IJ4+ 6.219,5.146 6.625,5.365 0.406,0.219 10 false B112 6.229,5.302 6.635,5.521 0.406,0.219 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM and/or injector assembly, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT INJECTOR ASSEMBLY
a.

Inspect the injector assembly.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

5.REPLACE INJECTOR ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Disconnect the injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-2 (#10) - B112-29 (IJ1+) Always Below 1 Ω
I1-1 (#1) - B112-59 (IJ1-) Always Below 1 Ω
I2-2 (#20) - B112-28 (IJ2+) Always Below 1 Ω
I2-1 (#2) - B112-58 (IJ2-) Always Below 1 Ω
I3-2 (#30) - B112-27 (IJ3+) Always Below 1 Ω
I3-1 (#3) - B112-57 (IJ3-) Always Below 1 Ω
I4-2 (#40) - B112-26 (IJ4+) Always Below 1 Ω
I4-1 (#4) - B112-56 (IJ4-) Always Below 1 Ω
I1-2 (#10) or B112-29 (IJ1+) - Body ground Always 10 kΩ or higher
I1-1 (#1) or B112-59 (IJ1-) - Body ground Always 10 kΩ or higher
I2-2 (#20) or B112-28 (IJ2+) - Body ground Always 10 kΩ or higher
I2-1 (#2) or B112-58 (IJ2-) - Body ground Always 10 kΩ or higher
I3-2 (#30) or B112-27 (IJ3+) - Body ground Always 10 kΩ or higher
I3-1 (#3) or B112-57 (IJ3-) - Body ground Always 10 kΩ or higher
I4-2 (#40) or B112-26 (IJ4+) - Body ground Always 10 kΩ or higher
I4-1 (#4) or B112-56 (IJ4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly of malfunctioning cylinder.

Click hereEngine / Hybrid System>2WW FUEL>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.PERFORM REGISTRATION
6.PERFORM REGISTRATION
a.

Register the injector assembly compensation code.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END