Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

Refer to DTC P0401.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0401

The EGR actuator is electrically opened or closed by the ECM. In order to ensure optimum control of the exhaust gas recirculation rate the ECM must continuously detect the exact position. The position of the EGR actuator is monitored by the EGR valve position sensor.

The DTC motor operates the EGR actuator. The position sensor is a Hall sensor. The Hall sensor detects the revolutions of the servo motor. The position of the EGR actuator is calculated.

The EGR position sensor is installed to the EGR valve assembly and is supplied with 5 V from the ECM.

A bridge circuit (H-bridge) is used to control the servo motor, which allows the servo motor to be operated in the opposite direction. The H-bridge circuit is monitored for diagnosis. An H-bridge electric circuit includes 5 switching elements, which are connected together in the form of the capital letter H.

A342512E01
4.031,1.208 3.823,0.521 3.823,0.521 3.646,0.521 true 3.552,2.906 3.198,3.333 3.198,3.333 3.021,3.333 true 2.708,0.406 4.542,0.604 1.833,0.198 10 false EGR Actuator 2.26,3.24 4.094,3.438 1.833,0.198 10 false EGR Cooler

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low EGR valve position sensor output voltage is 0.1 V or less for 0.22 seconds.
(3 trip detection logic)
·

Open or short in EGR valve position sensor (EGR valve assembly) circuit

·

EGR valve position sensor (EGR valve assembly)

·

ECM


Comes on DTC stored
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High EGR valve position sensor output voltage is 4.9 V or higher for 0.22 seconds.
(3 trip detection logic)
·

Open or short in EGR valve position sensor (EGR valve assembly) circuit

·

EGR valve position sensor (EGR valve assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0405
P0406
·

Actual EGR Valve Pos

·

Target EGR Valve Pos



WIRING DIAGRAM

A342507E07
0.51,1.688 2.802,1.885 2.292,0.198 10 false Position Sensor 0.74,2.823 3.031,3.021 2.292,0.198 10 false Actuator 0.458,3.24 2.75,3.438 2.292,0.198 10 false B131 0.469,3.396 2.76,3.594 2.292,0.198 10 false EGR Valve Assembly 1.688,0.5 3.979,0.698 2.292,0.198 10 false VC 1.698,1.323 3.99,1.521 2.292,0.198 10 false E2 1.688,1.99 3.979,2.188 2.292,0.198 10 false M+ 1.698,2.427 3.99,2.625 2.292,0.198 10 false M- 2.01,0.49 4.302,0.688 2.292,0.198 10 false 3 2.021,0.885 4.313,1.083 2.292,0.198 10 false 5 2.021,1.313 4.313,1.51 2.292,0.198 10 false 4 2.01,1.979 4.302,2.177 2.292,0.198 10 false 2 2.01,2.406 4.302,2.604 2.292,0.198 10 false 1 5.323,0.49 7.156,0.688 1.833,0.198 10 false 69 5.26,0.896 7.094,1.094 1.833,0.198 10 false 116 5.323,1.323 7.156,1.521 1.833,0.198 10 false 84 5.323,1.979 7.156,2.177 1.833,0.198 10 false 48 5.323,2.427 7.156,2.625 1.833,0.198 10 false 18 5.625,0.5 7.156,0.719 1.531,0.219 10 false VCEG 5.635,1 7.156,1.219 1.521,0.219 10 false EGLS 5.635,1.427 7.156,1.646 1.521,0.219 10 false EEGL 5.635,2.104 7.156,2.323 1.521,0.219 10 false EGM+ 5.635,2.521 7.156,2.74 1.521,0.219 10 false EGM- 5.979,3.042 6.51,3.25 0.531,0.208 10 false B112 5.99,3.208 6.5,3.427 0.51,0.219 10 false ECM 1.604,0.917 3.125,1.135 1.521,0.219 10 false VTA

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the EGR valve assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF FAN HIGH SPEED AND LOW SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Fan High Speed and Actuator Test of Fan Low Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan High Speed
50004 371 10
Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of Fan Low Speed
50004 371 11
OK:

Cooling fan operates according to operation.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

8.REPAIR OR REPLACE COOLING FAN SYSTEM
2.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B131-3 (VC) - B112-69 (VCEG) Always Below 1 Ω
B131-5 (VTA) - B112-116 (EGLS) Always Below 1 Ω
B131-4 (E2) - B112-84 (EEGL) Always Below 1 Ω
B131-3 (VC) or B112-69 (VCEG) - Body ground Always 10 kΩ or higher
B131-5 (VTA) or B112-116 (EGLS) - Body ground Always 10 kΩ or higher
B131-4 (E2) or B112-84 (EEGL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A372440C01
1.24,1.781 1.656,1.292 true 2.302,1.813 1.969,1.292 true 0.458,0.583 0.771,0.781 0.313,0.198 10 false *a 1.094,1.792 1.406,1.99 0.313,0.198 10 false VC 2.229,1.833 2.542,2.031 0.313,0.198 10 false E2
*a Front view of wire harness connector
(to EGR Valve Assembly)


a.

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B131-3 (VC) - B131-4 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE EGR VALVE ASSEMBLY

NG

6.REPLACE ECM
4.REPLACE EGR VALVE ASSEMBLY
a.

Replace the EGR valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR VALVE>REMOVAL


b.

Perform EGR learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0405 or P0406)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0405 or P0406)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P0405 or P0406 B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE COOLING FAN SYSTEM
a.

Repair or replace the cooling fan system.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END