Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1016  One of the Air Temperature Sensors  


DESCRIPTION

The ECM compares the values from each temperature sensor for appropriateness once per driving cycle during a cold start.

DTC P1016 is output when multiple values are determined to be inappropriate and the malfunctioning sensor cannot be determined.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1016 One of the Air Temperature Sensors When multiple temperature sensor values are compared and determined inappropriate, and inappropriate sensor cannot be determined for 0.05 seconds or more.
(3 trip detection logic)
·

Intake air temperature sensor

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

EGR gas temperature sensor

·

Ambient temperature sensor (built into ECM)


Does not come on DTC stored

Related Data List
DTC No. Data List
P1016
·

Intake Air

·

Intake Air Temp (Turbo)

·

Temperature Down Stream of EGR Cooler

·

Temperature of Environment Air



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the mass air flow meter sub-assembly, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1016)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

d.

Read the DTCs.

Result:
Result Proceed to
DTC P1016 A
DTC P1016 and other DTCs B


HINT:

If any DTCs other than P1016 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (INTAKE AIR, INTAKE AIR TEMP (TURBO), TEMPERATURE DOWN STREAM OF EGR COOLER AND TEMPERATURE OF ENVIRONMENT AIR)

B

2.READ VALUE USING GTS (INTAKE AIR, INTAKE AIR TEMP (TURBO), TEMPERATURE DOWN STREAM OF EGR COOLER AND TEMPERATURE OF ENVIRONMENT AIR)
NOTICE:

Perform the inspection while the engine is cool (engine coolant temperature within 25°C +/-5°C).


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air, Intake Air Temp (Turbo), Temperature Down Stream of EGR Cooler and Temperature of Environment Air.

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air
Intake Air Temp (Turbo)
Temperature Down Stream of EGR Cooler
Temperature of Environment Air
50003 371 4,54,197,143

d.

Read the value.

OK:

Difference between actual temperature and displayed temperature is 25°C (45°F) or less.


HINT:

Check the values and confirm the items to be replaced.


Result:
Result Items to be Replaced
Intake Air value is abnormal Mass air flow meter sub-assembly
Intake Air Temp (Turbo) value is abnormal Intake air temperature sensor
Temperature Down Stream of EGR Cooler value is abnormal EGR gas temperature sensor
Temperature of Environment Air ECM



Result:
Proceed to
NEXT



NEXT

3.REPLACE MALFUNCTIONING PARTS
3.REPLACE MALFUNCTIONING PARTS
a.

Replace the malfunctioning parts.


b.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

Perform the air flow meter learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION



c.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


d.

Replace the EGR gas temperature sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR GAS TEMPERATURE SENSOR>REMOVAL



Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END