Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1061  Charge Air Cooler Efficiency  


DESCRIPTION

Refer to DTC P007C.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P007C

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1061 Charge Air Cooler Efficiency Malfunctioning charge air cooler determined when calculated efficiency of charge air cooler is less than limit value for 0.22 seconds.
(3 trip detection logic)
·

Intake air temperature sensor

·

Intake system air leak

·

Dirty intercooler assembly fins

·

Intercooler assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1061 Intake Air Temp (Turbo)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMP (TURBO))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine and ECT > Data List
Tester Display
Intake Air Temp (Turbo)
50003 371 54

d.

Read the value.

OK:

-40°C (-40°F) to 120°C (248°F).



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)

NG

11.REPLACE INTAKE AIR TEMPERATURE SENSOR
2.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B115-1 (THA) - B112-79 (THIA) Always Below 1 Ω
B115-2 (E2) - B112-89 (ETHI) Always Below 1 Ω
B115-1 (THA) or B112-79 (THIA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE AIR TEMPERATURE SENSOR

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT INTAKE AIR TEMPERATURE SENSOR
a.

Inspect the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK INTAKE SYSTEM

NG

11.REPLACE INTAKE AIR TEMPERATURE SENSOR
4.CHECK INTAKE SYSTEM
a.

Start the engine.


b.

Check air duct between intake silencer, mass air flow meter sub-assembly and turbocharger for leaks.


c.

Check air duct between turbocharger and intake manifold for leaks.

HINT:
·

Oily patches are signs of leaks.

·

Check whether sealing rings on charge air hoses are rolled back or missing.



OK:

No leakage.



Result:
Proceed to
OK
NG



OK

5.CHECK INTERCOOLER ASSEMBLY FINS FOR DIRT

NG

10.REPAIR OR REPLACE INTAKE SYSTEM
5.CHECK INTERCOOLER ASSEMBLY FINS FOR DIRT
a.

Check intercooler assembly fins for dirt.


Result:
Proceed to
OK
NG



OK

6.REPLACE INTERCOOLER ASSEMBLY

NG

9.CLEAN INTERCOOLER ASSEMBLY
6.REPLACE INTERCOOLER ASSEMBLY
a.

Replace the intercooler assembly.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTERCOOLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P1061)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P1061)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P1061 is output B




A

END

B

8.REPLACE ECM
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CLEAN INTERCOOLER ASSEMBLY
a.

Clean the intercooler assembly fins.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning parts of the intake system.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE INTAKE AIR TEMPERATURE SENSOR
a.

Replace the intake air temperature sensor.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END