Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1401  Fault Code to Indicate a Defect of EGR Cooler Bypass Valve  


DESCRIPTION

Refer to DTC P245A.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P245A

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1401 Fault Code to Indicate a Defect of EGR Cooler Bypass Valve Even though EGR cooler bypass switching valve assembly operation conditions are met, temperature does not change after passing through EGR cooler.
(3 trip detection logic)
·

Vacuum system

·

EGR cooler bypass switching valve assembly

·

EGR cooler assembly


Does not come on DTC stored

Related Data List
DTC No. Data List
P1401 EGR Cooler Bypass Valve

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF EGR COOLER BYPASS VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Preparation before test.

i.

Disconnect vacuum line on vacuum unit of EGR cooler bypass.


ii.

Connect pressure gauge between vacuum line and vacuum unit.



e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of EGR Cooler Bypass Valve.

Powertrain > Engine and ECT > Active Test
Tester Display
Actuator Test of EGR Cooler Bypass Valve
50004 371 8

f.

Set the control value to 5%. The EGR cooler bypass valve must operate within 1 second. Valve travel when adjusted is approximately 10 mm.


g.

Check of vacuum system.

i.

Buildup of vacuum: vacuum is 650 hPa or more within 1 second.


ii.

Decrease of vacuum: vacuum is 0 to 50 hPa or less within 1 second.



h.

Wait for 2 seconds and set the control value to 95%. The EGR cooler bypass valve must operate within 1 second. Valve travel when adjusted is approximately 10 mm.


i.

Check of vacuum system.

i.

Buildup of vacuum: vacuum is 650 hPa or more within 1 second.


ii.

Decrease of vacuum: vacuum is 0 to 50 hPa or less within 1 second.



j.

Wait for 2 seconds and stop the operation using the EGR cooler bypass valve Active Test.

OK:

Operates smoothly when above procedure is performed.


HINT:

Check the movement of the EGR cooler bypass valve (stiffness, interference with other parts, etc.).



Result:
Proceed to
OK
NG



OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK VACUUM SUPPLY
2.CHECK VACUUM SUPPLY
a.

Check that vacuum is supplied to the EGR cooler bypass switching valve assembly.


Result:
Proceed to
OK
NG



OK

3.INSPECT EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY

NG

6.REPAIR OR REPLACE VACUUM SUPPLY
3.INSPECT EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Inspect the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.REPLACE EGR COOLER ASSEMBLY

NG

5.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
4.REPLACE EGR COOLER ASSEMBLY
a.

Replace the EGR cooler assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR COOLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Replace the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE VACUUM SUPPLY
a.

Repair or replace the source of the vacuum supply failure.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END