Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P245A  Exhaust Gas Recirculation Cooler Bypass Control Circuit / Open Bank 1  


DESCRIPTION

In order to lower the temperature of the recirculated exhaust gas and thus further reduce nitrogen oxide emissions, the exhaust gas is recirculated through the EGR cooler assembly. With this flap, the exhaust gas is guided at low temperatures past the cooling fins into a bypass channel and thus not cooled. Only at higher engine temperatures does the ECM open the bypass flap and the exhaust gas is cooled again.

This function reduces the HC emissions in cold operating conditions. The EGR cooler bypass switching valve assembly is opened during EGR operation if the coolant temperature is lower than 50°C (122°F).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245A Exhaust Gas Recirculation Cooler Bypass Control Circuit / Open Bank 1 Open detected in EGR cooler bypass switching valve assembly circuit for 0.22 seconds.
(3 trip detection logic)
·

EGR cooler bypass switching valve assembly

·

Open or short in EGR cooler bypass switching valve assembly circuit

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P245A EGR Cooler Bypass Valve

WIRING DIAGRAM

A351166E10
0.604,2.031 1.24,2.427 0.635,0.396 10 false EFI MAIN NO. 1 1.323,0.917 1.708,1.198 0.385,0.281 10 false 5 2.083,0.917 2.469,1.198 0.385,0.281 10 false 3 2.073,1.427 2.458,1.708 0.385,0.281 10 false 1 1.323,1.427 1.708,1.708 0.385,0.281 10 false 2 0.615,3.167 1.844,3.365 1.229,0.198 10 false FL MAIN 0.75,3.75 1.979,3.948 1.229,0.198 10 false Battery 6.156,3.833 6.76,4.073 0.604,0.24 10 false ECM 5.75,2.031 6.354,2.271 0.604,0.24 10 false MREL 5.375,2.135 5.979,2.375 0.604,0.24 10 false A62 5.729,1.031 6.333,1.271 0.604,0.24 10 false ECBV 5.323,1.031 5.927,1.271 0.604,0.24 10 false B112 5.396,0.854 6,1.094 0.604,0.24 10 false 16 5.448,1.948 6.052,2.188 0.604,0.24 10 false 9 3.51,1.354 4.115,1.594 0.604,0.24 10 false B109 3.521,1.521 5.417,2.115 1.896,0.594 10 false EGR Cooler Bypass Switching Valve Assembly 2.677,1.188 3.438,1.427 0.76,0.24 10 false EFI NO. 2 3.74,0.927 4.344,1.167 0.604,0.24 10 false 1 4.708,0.927 5.313,1.167 0.604,0.24 10 false 2 3.917,0.927 4.521,1.167 0.604,0.24 10 false +B 4.229,0.917 4.833,1.156 0.604,0.24 10 false ECBV 1.448,1.667 2.073,2.042 0.625,0.375 10 false EFI MAIN NO. 1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Inspect the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - ECM)

NG

10.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR cooler bypass switching valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B109-2 (ECBV) - B112-16 (ECBV) Always Below 1 Ω
B109-2 (ECBV) or B112-16 (ECBV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
A351155C03
0.333,1.083 0.729,1.292 0.396,0.208 2.5,1.76 1.885,1.292 false 0.156,0.188 0.469,0.344 0.313,0.156 10 false *a 0.375,1.104 0.823,1.365 0.448,0.26 10 false B109 2.563,1.74 3.01,2 0.448,0.26 10 false +B
*a Front view of wire harness connector
(to EGR Cooler Bypass Switching Valve Assembly)


Disconnect the EGR cooler bypass switching valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B109-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
4.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Replace the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P245A)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P245A)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P245A B




A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK HARNESS AND CONNECTOR (EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY - EFI MAIN NO. 1 RELAY)
a.

Disconnect the EGR cooler bypass switching valve assembly connector.


b.

Remove the EFI MAIN NO. 1 relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B109-1 (+B) - 3 (EFI MAIN NO. 1 relay holder) Always Below 1 Ω
B109-1 (+B) or 3 (EFI MAIN NO. 1 relay holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK ECM POWER SOURCE CIRCUIT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EGR COOLER BYPASS SWITCHING VALVE ASSEMBLY
a.

Replace the EGR cooler bypass switching valve assembly.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EGR BYPASS VALVE SWITCHING VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END