Home › Engine / Hybrid System › 2WW EMISSION CONTROL › EGR COOLER › from 2015.10
RM3090E _51 Engine / Hybrid System _044375 2WW EMISSION CONTROL _0210862 EGR COOLER A

2WW EMISSION CONTROL  EGR COOLER  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 12612A 4.REMOVE NO. 1 ENGINE COVER

Hide 51441 5.REMOVE NO. 1 ENGINE UNDER COVER

Hide 28899 8.REMOVE BATTERY INSULATOR

Hide 28800 9.REMOVE BATTERY

Hide 74431 10.REMOVE BATTERY TRAY

Hide 74414B 12.REMOVE BATTERY BRACKET REINFORCEMENT

Hide 17880 13.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY

Hide 17801 14.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17275A 16.DISCONNECT COMPRESSOR OUTLET ELBOW

Hide 17360A 19.DISCONNECT NO. 1 AIR TUBE ASSEMBLY

Hide 23801Q 20.DISCONNECT FUEL FEED PIPE SUB-ASSEMBLY

a.
A341635

Detach the 2 clamps and disconnect the engine wire.


b.
A341636

Remove the 2 bolts and disconnect the fuel feed pipe sub-assembly.


c.
A341637

Disconnect the vacuum hose from the No. 2 fuel hose.


d.

Disconnect the fuel feed pipe sub-assembly from the fuel pipe clamp.


Hide 22.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A341638

Disconnect the air fuel ratio sensor connector.


b.

Raise the air fuel ratio sensor connector to remove the air fuel ratio sensor connector from the bracket.


c.

Detach the 2 clamps and disconnect the air fuel ratio sensor.


d.

Detach the 2 clamps and disconnect the engine wire.


e.

Remove the 2 bolts and No. 1 exhaust manifold heat insulator.


Hide 25680 23.REMOVE EGR COOLER ASSEMBLY WITH EGR VALVE ASSEMBLY

a.
A341639

Disconnect the EGR valve assembly connector.


b.

Detach the clamp and disconnect the engine wire from the EGR valve assembly.


c.

Disconnect the hose clamp from the EGR cooler hose.


d.
A341640

Disconnect the vacuum hose from the EGR cooler assembly.


e.
A346730E01
2.906,1.896 3.104,2.135 0.198,0.24 10 true A 3.25,1.771 3.427,2.01 0.177,0.24 10 true A 2.573,2.094 2.771,2.333 0.198,0.24 10 true B 2.094,0.448 2.292,0.656 0.198,0.208 10 true B 0.448,0.635 0.604,0.844 0.156,0.208 10 true B 0.24,2.563 0.396,2.771 0.156,0.208 10 true C

Remove the 7 bolts and EGR cooler assembly with EGR valve assembly.

HINT:
·

When removing the bolts (A), use a T45 "TORX" socket wrench.

·

When removing the bolts (B), use a 6 mm hexagon wrench.

·

The bolt (C) in the illustration cannot be removed from the intake manifold.




f.

Remove the gasket.


g.
A341642

Remove the water pipe from the EGR cooler assembly.


Hide 25620 24.REMOVE EGR VALVE ASSEMBLY