Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1410  Enhanced SRC Check for the Adapted Diesel Particulate Filter Differential Pressure Too High  


DESCRIPTION

Refer to DTC P2454.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P2454

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1410 Enhanced SRC Check for the Adapted Diesel Particulate Filter Differential Pressure Too High Differential pressure sensor value exceeds upper limit for 1.5 seconds.
(3 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

Air hose

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1410 Adaptation Value of Differential Pressure at Particle Filter

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the differential pressure sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B127-1 (VC) - B112-70 (VCPX) Always Below 1 Ω
B127-2 (PEX) - B112-85 (PEX) Always Below 1 Ω
B127-3 (E2) - B112-71 (EPEX) Always Below 1 Ω
B127-1 (VC) or B112-70 (VCPX) - Body ground Always 10 kΩ or higher
B127-2 (PEX) or B112-85 (PEX) - Body ground Always 10 kΩ or higher
B127-3 (E2) or B112-71 (EPEX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351160C10
0.24,1.094 0.656,1.354 0.417,0.26 1.083,1.771 1.365,1.281 false 2.396,1.771 2.052,1.281 false 0.271,0.135 0.583,0.333 0.313,0.198 10 false *a 2.354,1.813 2.667,2.01 0.313,0.198 10 false E2 1,1.792 1.313,1.99 0.313,0.198 10 false VC 0.292,1.146 0.792,1.365 0.5,0.219 10 false B127
*a Front view of wire harness connector
(to Differential Pressure Sensor)


a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B127-1 (VC) - B127-3(E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION

NG

7.REPLACE ECM
3.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION
a.

Check the hose pipe from the exhaust emission system to the differential pressure sensor (for correct installation, sooting and leaks).

OK:

Part is securely installed.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (ADAPTATION VALUE OF DIFFERENTIAL PRESSURE AT PARTICLE FILTER)

NG

6.REPAIR AIR HOSE
4.READ VALUE USING GTS (ADAPTATION VALUE OF DIFFERENTIAL PRESSURE AT PARTICLE FILTER)
NOTICE:

The EGR valve is closed during the test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Adaptation Value of Differential Pressure at Particle Filter.

Powertrain > Engine and ECT > Data List
Tester Display
Adaptation Value of Differential Pressure at Particle Filter
50003 371 116

d.

Start the engine and warm it up until the engine coolant temperature is 80°C (176°F) or higher.


e.

Test 1

i.

Idle the engine for 2 seconds.


ii.

Read the value for 10 seconds.

OK:

With the ignition switch ON, "Adaptation Value of Differential Pressure at Particle Filter" value is within 3.5 kPa.




f.

Test 2

i.

Maintain the engine speed at 2000 rpm for 2 seconds.


ii.

Maintain the engine speed at 2000 rpm and read the value for 10 seconds.

OK:

With the ignition switch ON, "Adaptation Value of Differential Pressure at Particle Filter" value is within 7.5 kPa.




g.

Test 3

i.

With the engine running without load at approximately 3800 rpm, wait for 2 seconds.


ii.

With the engine running without load at approximately 3800 rpm, read the value for 10 seconds.

OK:

With the ignition switch ON, "Adaptation Value of Differential Pressure at Particle Filter" value is within 20 kPa.




Result:
Proceed to
OK
NG



OK

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

5.REPLACE DIFFERENTIAL PRESSURE SENSOR
5.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


b.

Perform the differential pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR AIR HOSE
a.

Install the air hose.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END