Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1432  Particulate Filter Efficiency  


DESCRIPTION

HINT:

For more information on the diesel particulate filter (DPF) catalyst regeneration control, refer to System Description.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1432 Particulate Filter Efficiency Amount of soot in DPF catalytic converter lower than estimated lower limit.
(3 trip detection logic)
·

Differential pressure sensor

·

Exhaust manifold converter sub-assembly (DPF catalytic converter)

·

Air hose

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1432 Adaptation Value of Differential Pressure at Particle Filter

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the DPF catalyst, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the differential pressure sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Check that the DPF catalytic converter is installed.

OK:

DPF catalytic converter is installed.


HINT:

If the DPF catalytic converter is not installed, the exhaust tailpipe turns black from soot.



b.

Check that the DPF catalytic converter is not damaged.

OK:

DPF catalytic converter is not damaged.


HINT:
·

If the DPF catalytic converter is damaged, the exhaust tailpipe and edge of the filter turn black from soot.

·

Disconnect the front exhaust pipe assembly from the exhaust manifold converter sub-assembly (DPF catalytic converter) and check for soot stuck inside the exhaust manifold converter sub-assembly (DPF catalytic converter).




Result:
Proceed to
OK
NG



OK

2.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION

NG

7.INSTALL OR REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
2.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION
a.

Check that the differential pressure sensor air hose is securely installed.

OK:

Part is securely installed.



Result:
Proceed to
OK
NG



OK

3.CHECK DIFFERENTIAL PRESSURE SENSOR

NG

6.CONNECT AIR HOSE
3.CHECK DIFFERENTIAL PRESSURE SENSOR
a.

Check for DTCs related to the differential pressure sensor.

OK:

DTCs related to the differential pressure sensor are not output.



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Repair or replace the differential pressure sensor or perform inspections and troubleshooting for related DTCs.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

HINT:

When the differential pressure sensor is replaced, perform initialization.



Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONNECT AIR HOSE
a.

Install the air hose.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.INSTALL OR REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (DPF CATALYTIC CONVERTER)
a.

Install or replace the exhaust manifold converter sub-assembly (DPF catalytic converter).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>MONOLITHIC CONVERTER>REMOVAL


b.

Perform DPF history information reset and NOx storage catalyst learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END