Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P1477  Swirl Valve Circuit Error  P2008  Open Load Error  P2009  Intake Manifold Runner Control Circuit Low Bank 1  P2010  Intake Manifold Runner Control Circuit High Bank 1  


DESCRIPTION

Refer to DTC P2016.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P2016

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1477 Swirl Valve Circuit Error Either condition is met (3 trip detection logic):
·

An overload due to a short circuit in the battery is detected in the swirl control valve circuit for 0.2 seconds.

·

Swirl control valve circuit over temperature for 0.2 seconds.

·

Swirl control valve circuit overcurrent for 0.2 seconds.


·

Open or short in swirl control valve circuit

·

Swirl control valve

·

ECM


Does not come on DTC stored
P2008 Open Load Error Open in swirl control valve actuator circuit for 0.2 seconds.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve

·

ECM


Does not come on DTC stored
P2009 Intake Manifold Runner Control Circuit Low Bank 1 Ground short in swirl control valve actuator circuit for 0.2 seconds.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve

·

ECM


Does not come on DTC stored
P2010 Intake Manifold Runner Control Circuit High Bank 1 Battery short in swirl control valve actuator circuit for 0.2 seconds.
(3 trip detection logic)
·

Open or short in swirl control valve circuit

·

Swirl control valve

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P1477
P2008
P2009
P2010
Swirl Valve Actuator Position

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the swirl control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.

Powertrain > Engine and ECT > Active Test
Active Test Display
Actuator Test of Swirl Flap
Data List Display
Swirl Valve Actuator Position
50004 371 7 198
OK:

The value of "Swirl Valve Actuator Position" changes according to the amount "Actuator Test of Swirl Flap" is operated, and the swirl flap operates smoothly.



Result:
Proceed to
OK
NG



OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)
2.CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)
a.

Disconnect the swirl control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B129-3 (SCV+) - B112-49 (IA1+) Always Below 1 Ω
B129-4 (SCV-) - B112-19 (IA1-) Always Below 1 Ω
B129-3 (SCV+) or B112-49 (IA1+) - Body ground Always 10 kΩ or higher
B129-4 (SCV-) or B112-19 (IA1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE SWIRL CONTROL VALVE

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE SWIRL CONTROL VALVE
a.

Replace the swirl control valve.

Click hereEngine / Hybrid System>2WW INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Perform the swirl valve learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P1477, P2008, P2009 AND/OR P2010)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P1477, P2008, P2009 AND/OR P2010)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P1477, P2008, P2009 and/or P2010 B




A

END

B

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END