Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2032  Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2  P2033  Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2  


DESCRIPTION

Refer to DTC P0545.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0545

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2032 Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2 Exhaust gas temperature sensor (for sensor 2) output voltage is 0.049 V or less for 0.6 seconds or more.
(3 trip detection logic)
·

Open or short in exhaust gas temperature sensor (for sensor 2) circuit

·

Exhaust gas temperature sensor (for sensor 2)

·

ECM


Comes on DTC stored
P2033 Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2 Exhaust gas temperature sensor (for sensor 2) output voltage is 4.99 V or more for 0.6 seconds or more.
(3 trip detection logic)
·

Open or short in exhaust gas temperature sensor (for sensor 2) circuit

·

Exhaust gas temperature sensor (for sensor 2)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2032
P2033
Exhaust Temperature B1S2

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION


HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2)
a.

Using the GTS, check the value of Exhaust Temperature B1S2.

i.

Connect the GTS to the DLC3.


ii.

Start the engine and warm it up.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Exhaust Temperature B1S2.

Powertrain > Engine and ECT > Data List
Tester Display
Exhaust Temperature B1S2
50003 371 59

v.

Read the value.

Standard:

Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling after warm-up).




b.

Inspect the exhaust gas temperature sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR(for Sensor 2)>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2) - ECM)

NG

5.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2)
2.CHECK HARNESS AND CONNECTOR (EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2) - ECM)
a.

Disconnect the exhaust gas temperature sensor (for sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B110-1 (THCO) - B112-109 (THCO) Always Below 1 Ω
B110-2 (E2) - B112-110 (ETCO) Always Below 1 Ω
B110-1 (THCO) or B112-109 (THCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EXHAUST GAS TEMPERATURE SENSOR (FOR SENSOR 2)
a.

Replace the exhaust gas temperature sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR(for Sensor 2)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END