Refer to DTC P0030.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2195 | O2 Sensor Signal Biased / Stuck Lean Bank 1 Sensor 1 | Oxygen concentration higher than estimated concentration for specified condition.
(3 trip detection logic) |
·
Open or short in air fuel ratio sensor (for sensor 1) circuit ·
Air fuel ratio sensor (for sensor 1) ·
Exhaust system exhaust gas leak ·
ECM |
Does not come on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2195 | ·
O2 Sensor Lambda Bank 1 Sensor 1 ·
O2 Sensor Lambda Bank 1 Sensor 2 |
Refer to DTC P0030.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030
When replacing the ECM and/or air fuel ratio sensor, the ECM needs registration and initialization.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Air fuel ratio sensors functional check
Refer to DTC P013A.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P013A
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2195 | A |
| DTC P2195 and other DTCs | B |
If any DTCs other than P2195 are output, troubleshoot those DTCs first.
If a DTC is stored for the heater system of the air fuel ratio sensor, first repair the heater system.
A
B
Check for exhaust gas leak from the exhaust system.
No exhaust gas leak.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air fuel ratio sensor (for sensor 1) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B107-1 (AF1+) - B112-127 (AF1+) | Always | Below 1 Ω |
| B107-2 (AF1-) - B112-126 (AF1-) | Always | Below 1 Ω |
| B107-3 (HAF1) - B112-46 (HAF1) | Always | Below 1 Ω |
| B107-5 (TR1) - B112-128 (TR1) | Always | Below 1 Ω |
| B107-6 (RE1) - B112-125 (RE1) | Always | Below 1 Ω |
| B107-1 (AF1+) or B112-127 (AF1+) - Body ground | Always | 10 kΩ or higher |
| B107-2 (AF1-) or B112-126 (AF1-) - Body ground | Always | 10 kΩ or higher |
| B107-3 (HAF1) or B112-46 (HAF1) - Body ground | Always | 10 kΩ or higher |
| B107-5 (TR1) or B112-128 (TR1) - Body ground | Always | 10 kΩ or higher |
| B107-6 (RE1) or B112-125 (RE1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor (for sensor 1).
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 1)>REMOVAL
Perform the O2 sensor learning value reset.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC output | A |
| DTC P2195 | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the exhaust system.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 60 seconds or more [A].
Perform road test [B].
Repeat [A] and [B] for the number of trips detected.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT