Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2270  O2 Sensor Signal Biased / Stuck Lean Bank 1 Sensor 2  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2270 O2 Sensor Signal Biased / Stuck Lean Bank 1 Sensor 2 The oxygen concentration measured by the air fuel ratio sensor (for sensor 2) is excessively higher than the estimated oxygen concentration.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

Exhaust system exhaust gas leak


Does not come on DTC stored

Related Data List
DTC No. Data List
P2270
·

O2 Sensor Lambda Bank 1 Sensor 1

·

O2 Sensor Lambda Bank 1 Sensor 2



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the Air Fuel Ratio Sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



Air fuel ratio sensors functional check


Refer to DTC P013A.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P013A


PROCEDURE

1.CHECK EXHAUST SYSTEM
a.

Check for exhaust gas leaks in the exhaust system.

OK:

No leakage.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)

NG

5.REPAIR OR REPLACE EXHAUST SYSTEM
2.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-1 (AF2+) - B112-130 (AF2+) Always Below 1 Ω
B133-2 (AF2-) - B112-133 (AF2-) Always Below 1 Ω
B133-3 (HAF2) - B112-17 (HAF2) Always Below 1 Ω
B133-5 (TR2) - B112-131 (TR2) Always Below 1 Ω
B133-6 (RE2) - B112-134 (RE2) Always Below 1 Ω
B133-1 (AF2+) or B112-130 (AF2+) - Body ground Always 10 kΩ or higher
B133-2 (AF2-) or B112-133 (AF2-) - Body ground Always 10 kΩ or higher
B133-3 (HAF2) or B112-17 (HAF2) - Body ground Always 10 kΩ or higher
B133-5 (TR2) or B112-131 (TR2) - Body ground Always 10 kΩ or higher
B133-6 (RE2) or B112-134 (RE2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Replace the air fuel ratio sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 2)>REMOVAL


b.

Perform O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE EXHAUST SYSTEM
a.

Repair or replace the malfunctioning parts of the exhaust system.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END