Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P22AB  O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 2  P22AC  O2 Sensor Positive Current Control Circuit Low Bank 1 Sensor 2  P22AD  O2 Sensor Positive Current Control Circuit High Bank 1 Sensor 2  P22AE  O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 2  P22B2  O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 2  


DESCRIPTION

Refer to DTC P0030.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P0030

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P22AB O2 Sensor Positive Current Control Circuit/Open Bank 1 Sensor 2 The air-fuel ratio is not detected as rich, but the output of the air fuel ratio sensor (for sensor 2) is less than the lower limit value for 2 seconds.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored
P22AC O2 Sensor Positive Current Control Circuit Low Bank 1 Sensor 2 Ground short in air fuel ratio sensor (for sensor 2) circuit for 2 seconds.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored
P22AD O2 Sensor Positive Current Control Circuit High Bank 1 Sensor 2 Battery short in air fuel ratio sensor (for sensor 2) circuit for 2 seconds.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored
P22AE O2 Sensor Reference Voltage Circuit/Open Bank 1 Sensor 2 Air fuel ratio sensor (for sensor 2) is detected if the signal voltage is more than 3 V and the non-linearized value of the air fuel ratio sensor (for sensor 2) signal is greater than 1.5 V or less than -1.3 V for 0.5 seconds.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored
P22B2 O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 2 Air fuel ratio sensor (for sensor 2) is detected if the signal voltage is more than 3 V and the non-linearized value of the air fuel ratio sensor (for sensor 2) signal lies between -0.1 V and 0.1 V for 0.5 seconds.
(3 trip detection logic)
·

Open or short in air fuel ratio sensor (for sensor 2) circuit

·

Air fuel ratio sensor (for sensor 2)

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P22AB
P22AC
P22AD
P22AE
P22B2
O2 Sensor Lambda Bank 1 Sensor 2

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the air fuel ratio sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (FOR SENSOR 2) - ECM)
a.

Disconnect the air fuel ratio sensor (for sensor 2) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B133-1 (AF2+) - B112-130 (AF2+) Always Below 1 Ω
B133-2 (AF2-) - B112-133 (AF2-) Always Below 1 Ω
B133-3 (HAF2) - B112-17 (HAF2) Always Below 1 Ω
B133-5 (TR2) - B112-131 (TR2) Always Below 1 Ω
B133-6 (RE2) - B112-134 (RE2) Always Below 1 Ω
B133-1 (AF2+) or B112-130 (AF2+) - Body ground Always 10 kΩ or higher
B133-2 (AF2-) or B112-133 (AF2-) - Body ground Always 10 kΩ or higher
B133-3 (HAF2) or B112-17 (HAF2) - Body ground Always 10 kΩ or higher
B133-5 (TR2) or B112-131 (TR2) - Body ground Always 10 kΩ or higher
B133-6 (RE2) or B112-134 (RE2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE AIR FUEL RATIO SENSOR (FOR SENSOR 2)
a.

Replace the air fuel ratio sensor (for sensor 2).

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>AIR FUEL RATIO SENSOR(for Sensor 2)>REMOVAL


b.

Perform the O2 sensor learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
DTC P22AB, P22AC, P22AD, P22AE and/or P22B2 A
No DTC output B




A

4.REPLACE ECM

B

END

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END