Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM C

2WW ENGINE CONTROL  ECD SYSTEM  P2453  Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

Refer to DTC P2454.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>P2454

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2453 Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance The difference between the differential pressure sensor output value and the ambient pressure sensor output value is more than 60 mbar (6 kPa) for 0.05 seconds.
(3 trip detection logic)
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

Differential pressure sensor pipe

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2453 Filtered Pressure Value at Particle Filter Upstream

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

After replacing the differential pressure sensor, the ECM needs initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION



HINT:
·

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Atmosphere Pressure and Filtered Pressure Value at Particle Filter Upstream.

Powertrain > Engine and ECT > Data List
Tester Display
Atmosphere Pressure
Filtered Pressure Value at Particle Filter Upstream
50003 371 5,117

d.

Read the value.

OK:

Difference between the Atmosphere Pressure and the Filtered Pressure Value at Particle Filter Upstream is less than 8 kPa.



Result:
Proceed to
OK
NG



OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION
2.CHECK DIFFERENTIAL PRESSURE SENSOR AIR HOSE CONNECTION
a.

Check if the exhaust pipe air hose routing between the differential pressure sensor and the vacuum transmitting pipe is correct.


b.

Check that there is no exhaust gas leak between the differential pressure sensor and the vacuum transmitting pipe.

OK:

Exhaust pipe air hose routing is correct and there is no exhaust gas leak.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)

NG

9.REPAIR OR REPLACE MALFUNCTIONING PARTS
3.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B127-1 (VC) - B112-70 (VCPX) Always Below 1 Ω
B127-2 (PEX) - B112-85 (PEX) Always Below 1 Ω
B127-3 (E2) - B112-71 (EPEX) Always Below 1 Ω
B127-1 (VC) or B112-70 (VCPX) - Body ground Always 10 kΩ or higher
B127-2 (PEX) or B112-85 (PEX) - Body ground Always 10 kΩ or higher
B127-3 (E2) or B112-71 (EPEX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (VC VOLTAGE)
A351158C26
0.302,1.146 0.75,1.365 0.448,0.219 0.948,1.792 1.354,1.281 true 2.438,1.792 2.083,1.281 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.375,1.167 0.844,1.365 0.469,0.198 10 false B127 0.844,1.813 1.313,2.01 0.469,0.198 10 false VC 2.396,1.813 2.865,2.01 0.469,0.198 10 false E2
*a Front view of wire harness connector
(to Differential Pressure Sensor)


a.

Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B127-1 (VC) - B127-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

7.REPLACE ECM
5.REPLACE DIFFERENTIAL PRESSURE SENSOR
a.

Replace the differential pressure sensor.

Click hereEngine / Hybrid System>2WW EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


b.

Perform the differential pressure learning value reset.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2453)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2453)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Read the DTCs.

Result:
Result Proceed to
No DTC output A
DTC P2453 B




A

END

B

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace the malfunctioning parts.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 371

d.

Turn the ignition switch off and wait for 60 seconds or more [A].


e.

Perform road test [B].


f.

Repeat [A] and [B] for the number of trips detected.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 371

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END