Home › Engine / Hybrid System › 2WW ENGINE CONTROL › ECD SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _044372 2WW ENGINE CONTROL _0208480 ECD SYSTEM J

2WW ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

w/o Entry and Start System:

While the engine is being cranked, current flows from terminal ST2 of the ignition switch assembly to the clutch start switch assembly and also flows to terminal STA of the ECM (STA Signal).


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the ECM, the ECM needs registration and initialization.

Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECD SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.


PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

2.INSPECT STARTER RELAY (ST)

B

9.READ VALUE USING GTS (STARTER SIGNAL)
2.INSPECT STARTER RELAY (ST)
a.

Inspect the starter relay (ST).

Click hereEngine / Hybrid System>2WW STARTING>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (STARTER SIGNAL)

NG

REPLACE STARTER RELAY (ST)

3.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 371 149

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY HOLDER TERMINAL VOLTAGE)

NG

7.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH TERMINAL VOLTAGE)
4.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY HOLDER TERMINAL VOLTAGE)
A296486C05
0.083,0.073 0.396,0.229 0.313,0.156 10 *1 2.104,3.479 2.417,3.635 0.313,0.156 10 *2
*1 Engine Room Relay Block and Junction Block
*2 ST Relay


a.

Remove the ST NO. 1 relay from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (ST relay holder) - Body ground Cranking 11 to 14 V
5 (ST relay holder) - Body ground Always 11 to 14 V



Result:
Result Proceed to
OK A
NG (ST relay holder terminal 1) B
NG (ST relay holder terminal 5) C



A

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ST NO. 1 RELAY HOLDER)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY HOLDER)

5.CHECK HARNESS AND CONNECTOR (STARTER RELAY (ST) - BODY GROUND)
a.

Remove the starter relay (ST) from the engine room relay block and junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - STARTER RELAY (ST))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - STARTER RELAY (ST))
a.

Remove the starter relay (ST) from the engine room relay block and junction block.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B117-1 - 3 (Starter relay (ST) holder) Always Below 1 Ω
B117-1 or 3 (Starter relay (ST) holder) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH TERMINAL VOLTAGE)
A257647C09
0.729,0.802 1.094,1.021 0.365,0.219 0.74,1.125 1.104,1.344 0.365,0.219 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 0.833,0.823 1.156,1.031 0.323,0.208 10 false A4 0.854,1.156 1.177,1.365 0.323,0.208 10 false F2 1.156,0.802 1.469,1 0.313,0.198 10 false *1 1.167,1.115 1.479,1.313 0.313,0.198 10 false *2
*a Front view of wire harness connector
(to Clutch Start Switch Assembly)
*1 for LHD
*2 for RHD


a.

Disconnect the clutch start switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A4-2 - Body ground Cranking 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
F2-2 - Body ground Cranking 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH TERMINAL VOLTAGE)
8.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY HOLDER)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

9.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 371 149

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

12.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY (ST))
10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH TERMINAL VOLTAGE)
A257670C05
0.344,1.094 0.708,1.344 0.365,0.25 2.375,1.813 2.208,1.177 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 0.438,1.135 0.74,1.333 0.302,0.198 10 false G4 2.281,1.844 2.74,2.042 0.458,0.198 10 false AM2
*a Front view of wire harness connector
(to Ignition Switch Assembly)


a.

Disconnect the ignition switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G4-4 (AM2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

11.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2WW STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (ECM - STARTER RELAY (ST))
a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Remove the starter relay (ST) from the engine room relay block and junction block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-36 (STA) - 2 (Starter relay (ST) holder) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR