Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › from 2015.10
RM3090E _55 Steering _008772 POWER ASSIST SYSTEMS _0049011 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  Power Steering Warning Light Circuit  


DESCRIPTION

The power steering ECU is connected to the combination meter via CAN communication. If any of the following conditions are detected, the power steering warning light remains on.

·

The circuit that supplies power source voltage to the power steering ECU assembly (terminal IG) is open.

·

The power supply voltage to the power steering ECU assembly (terminals IG and PIG) drops.


WIRING DIAGRAM

C277340E01
5.875,3.99 6.854,4.479 0.979,0.49 10 false Power Steering ECU Assembly 0.979,4.365 2.76,4.656 1.781,0.292 10 false CAN Communication Line 1.698,2.385 2.75,2.667 1.052,0.281 10 false from IG Circuit 0.094,1.375 2.146,1.615 2.052,0.24 10 false Combination Meter Assembly 1.177,2.958 2.958,3.25 1.781,0.292 10 false Stop and Start System 3.438,2.563 4.167,2.813 0.729,0.25 10 false EPS-IG 4.625,2.385 5,2.635 0.375,0.25 10 false hG1 4.698,2.167 4.948,2.365 0.25,0.198 10 false 5 5.646,2.396 5.948,2.667 0.302,0.271 10 false h1 6,3.5 6.479,3.74 0.479,0.24 10 false PGND 6,2.396 6.302,2.667 0.302,0.271 10 false IG 5.615,1.667 5.917,1.938 0.302,0.271 10 false h2 5.667,3.271 5.969,3.5 0.302,0.229 10 false 2 5.667,2.167 5.958,2.365 0.292,0.198 10 false 1 3.854,2.25 4.167,2.5 0.313,0.25 10 false *2 3.854,2.833 4.167,3.083 0.313,0.25 10 false *3 5.167,2.25 5.479,2.5 0.313,0.25 10 false *1 5.167,3.333 5.479,3.583 0.313,0.25 10 false *1 0.417,3.49 2.469,3.781 2.052,0.292 10 false *1: ECU Wire Sub-assembly 0.417,3.771 2.583,4.031 2.167,0.26 10 false *2: w/o Stop and Start System 0.427,4.052 2.521,4.313 2.094,0.26 10 false *3: w/ Stop and Start System 1.833,1.667 2.719,1.917 0.885,0.25 10 false from Battery 3.521,1.833 3.917,2.083 0.396,0.25 10 false EPS 4.625,1.667 5,1.917 0.375,0.25 10 false Ah1 4.688,1.458 4.938,1.656 0.25,0.198 10 false 1 5.667,1.469 5.917,1.667 0.25,0.198 10 false 1 5.646,3.479 5.948,3.75 0.302,0.271 10 false h2 6,1.667 6.302,1.938 0.302,0.271 10 false PIG 5.146,1.542 5.458,1.792 0.313,0.25 10 false *1

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION AND GROUND WIRE
a.

Check the connection condition of the ECU wire sub-assembly and power steering ECU assembly connectors.

OK:

The ECU wire sub-assembly and power steering ECU assembly connectors are securely connected.



b.

Check that the ground wire is securely installed with the bolt.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION

OK:

The ground wire is securely installed with the bolt.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

NG

CONNECT CONNECTOR OR INSTALL GROUND WIRE

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY)

NG

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY)
a.
C278679C01
0.729,0.635 1.167,0.938 0.438,0.302 1.958,1.406 2.51,1.427 false 2.594,1.365 2.906,1.615 0.313,0.25 10 IG 0.833,0.708 1.146,0.906 0.313,0.198 10 hG1 0.135,0.094 0.448,0.25 0.313,0.156 10 *a
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the hG1 ECU wire sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
hG1-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

4.CHECK ECU WIRE SUB-ASSEMBLY

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

4.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240351C03
0.344,3.271 0.792,3.552 0.448,0.281 0.604,0.906 1.052,1.188 0.448,0.281 2.271,3.531 2.354,4.135 false 1.115,1.677 1.49,1.802 false 0.198,0.146 0.635,0.458 0.438,0.313 10 *a 0.51,3.333 0.948,3.729 0.438,0.396 10 h2 2.177,4.177 2.906,4.51 0.729,0.333 10 PGND 0.917,1.583 1.344,1.948 0.427,0.365 10 IG 0.771,0.969 1.156,1.354 0.385,0.385 10 h1
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the hG1 connector to the ECU wire sub-assembly.


b.

Disconnect the h1 and h2 power steering ECU assembly connectors.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
h1-1 (IG) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (BATTERY - ECU WIRE SUB-ASSEMBLY)
a.
C277337C01
0.594,0.781 1.042,1.125 0.448,0.344 1.813,1.229 2.417,0.99 false 0.146,0.104 0.458,0.333 0.313,0.229 10 *a 2.51,0.917 2.917,1.177 0.406,0.26 10 PIG 0.708,0.875 1.167,1.146 0.458,0.271 10 Ah1
*a Front view of wire harness connector
(to ECU Wire Sub-assembly)


Disconnect the Ah1 ECU wire sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Ah1-1 (PIG) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK ECU WIRE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECU WIRE SUB-ASSEMBLY
a.
C240344C05
0.229,1 0.677,1.281 0.448,0.281 1.198,1.198 1.115,1.792 false 0.146,0.125 0.74,0.552 0.594,0.427 10 *a 0.396,1.052 0.854,1.375 0.458,0.323 10 h2 1.021,1.823 1.521,2.146 0.5,0.323 10 PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the Ah1 connector to the ECU wire sub-assembly.


b.

Disconnect the h2 power steering ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h2-1 (PIG) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE ECU WIRE SUB-ASSEMBLY

7.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the h1 and h2 power steering ECU assembly connectors.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. EPS
50004 122 22

c.

Check the combination meter assembly.

OK:

The power steering warning light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY