This DTC is output when the vehicle stability control system has a problem. Check the vehicle stability control system when this DTC is output.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P1578 | Brake System | The ECM receives a brake system error signal for 0.2 seconds or more. | ·
Vehicle stability control system ·
Skid control ECU (brake actuator assembly) ·
ECM |
This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Trouble Codes.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
for 2AD-FTV, 2AD-FHV:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
for 2WW:
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Enter the following menus: Powertrain / Cruise Control / Trouble Codes.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
for 2AD-FTV, 2AD-FHV:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
for 2WW:
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P1578 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Trouble Codes.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
for 2AD-FTV, 2AD-FHV:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
for 2WW:
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Enter the following menus: Powertrain / Cruise Control / Trouble Codes.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
for 2AD-FTV, 2AD-FHV:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
for 2WW:
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P1578 is output | B |
A
B
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL