Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2015.10–2016.08
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

·

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.

·

The ECM receives the brake demand signal from the driving support ECU assembly and transmits it to the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) receives a signal from the ECM and operates the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) operates the brake actuator assembly and at the same time illuminates the stop light by operating the stop light control ECU assembly*1 or STOP LP relay (stop light control relay)*2.


DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit
·

When the ignition switch is turned ON and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more.

·

While the dynamic radar cruise control system is operating (vehicle-to-vehicle distance control mode), the ECM detects the stop light control ECU assembly error signal from the skid control ECU (brake actuator assembly) for approximately 0.2 seconds or more*1.

·

While the dynamic radar cruise control system is operating (vehicle-to-vehicle distance control mode), the ECM detects the STOP LP Relay (stop light control relay) signal from the skid control ECU (brake actuator assembly) for approximately 0.2 seconds or more*2.


·

Stop light switch assembly

·

Stop light switch circuit

·

ECM


·

Stop light control ECU assembly*1

·

STOP LP relay (stop light control relay)*2

·

Stop light control ECU assembly circuit*1

·

STOP LP relay(Stop light control relay) circuit*2

·

Skid control ECU (brake actuator assembly)

·

ECM



*1: for LED Type Stop Light

*2: for Bulb Type Stop Light


WIRING DIAGRAM

E288572E34
5.896,1.833 6.396,2.052 0.5,0.219 10 false ECM 5.583,0.99 5.75,1.188 0.167,0.198 10 false 11 5.604,0.427 5.771,0.625 0.167,0.198 10 false 24 4.135,0.979 4.302,1.177 0.167,0.198 10 false 3 4.135,0.427 4.302,0.625 0.167,0.198 10 false 5 3.177,0.313 3.344,0.51 0.167,0.198 10 false 7 3.177,0.823 3.344,1.021 0.167,0.198 10 false 6 3.177,1.156 3.344,1.354 0.167,0.198 10 false 2 2.927,1.885 4.75,2.094 1.823,0.208 10 false Stop Light Switch Assembly 2.927,1.708 3.385,1.906 0.458,0.198 10 false A77 3.354,1.292 3.813,1.49 0.458,0.198 10 false GND 3.354,0.948 3.51,1.146 0.156,0.198 10 false B 3.354,0.448 3.51,0.646 0.156,0.198 10 false B 3.938,1.104 4.094,1.302 0.156,0.198 10 false L 3.917,0.563 4.375,0.76 0.458,0.198 10 false L 2.167,0.625 2.781,0.823 0.615,0.198 10 false STOP 2.24,1.125 2.896,1.333 0.656,0.208 10 false IGN 0.406,0.417 1.344,0.615 0.938,0.198 10 false from Battery 0.25,0.927 1.198,1.313 0.948,0.385 10 false from IG2 Relay 5.865,1.094 6.323,1.292 0.458,0.198 10 false STP 5.875,0.552 6.49,0.75 0.615,0.198 10 false ST1- 5.854,1.667 6.313,1.865 0.458,0.198 10 false A62 0.073,0.052 4.479,0.292 4.406,0.24 12 false for 2AR-FE:

E288572E35
5.896,1.833 6.396,2.052 0.5,0.219 10 false ECM 5.656,0.99 5.823,1.188 0.167,0.198 10 false 9 5.604,0.427 5.771,0.625 0.167,0.198 10 false 10 4.135,0.979 4.302,1.177 0.167,0.198 10 false 3 4.135,0.427 4.302,0.625 0.167,0.198 10 false 5 3.177,0.313 3.344,0.51 0.167,0.198 10 false 7 3.177,0.823 3.344,1.021 0.167,0.198 10 false 6 3.177,1.156 3.344,1.354 0.167,0.198 10 false 2 2.927,1.885 4.75,2.094 1.823,0.208 10 false Stop Light Switch Assembly 2.927,1.708 3.385,1.906 0.458,0.198 10 false A77 3.354,1.292 3.813,1.49 0.458,0.198 10 false GND 3.354,0.948 3.51,1.146 0.156,0.198 10 false B 3.354,0.448 3.51,0.646 0.156,0.198 10 false B 3.938,1.104 4.094,1.302 0.156,0.198 10 false L 3.917,0.563 4.375,0.76 0.458,0.198 10 false L 2.167,0.625 2.781,0.823 0.615,0.198 10 false STOP 2.24,1.125 2.896,1.333 0.656,0.208 10 false IGN 0.406,0.417 1.344,0.615 0.938,0.198 10 false from Battery 0.25,0.927 1.198,1.313 0.948,0.385 10 false from IG2 Relay 5.865,1.094 6.323,1.292 0.458,0.198 10 false STP 5.875,0.552 6.49,0.75 0.615,0.198 10 false ST1- 5.854,1.667 6.313,1.865 0.458,0.198 10 false A62 0.073,0.052 4.479,0.292 4.406,0.24 12 false for 3ZR-FAE, 3ZR-FE:

E288572E38
5.896,1.833 6.396,2.052 0.5,0.219 10 false ECM 5.583,0.99 5.896,1.229 0.313,0.24 10 false 35 5.604,0.427 5.771,0.625 0.167,0.198 10 false 34 4.135,0.979 4.302,1.177 0.167,0.198 10 false 3 4.135,0.427 4.302,0.625 0.167,0.198 10 false 5 3.177,0.313 3.344,0.51 0.167,0.198 10 false 7 3.177,0.823 3.344,1.021 0.167,0.198 10 false 6 3.177,1.156 3.344,1.354 0.167,0.198 10 false 2 2.927,1.885 4.75,2.094 1.823,0.208 10 false Stop Light Switch Assembly 2.927,1.708 3.385,1.906 0.458,0.198 10 false A77 3.354,1.292 3.813,1.49 0.458,0.198 10 false GND 3.354,0.948 3.51,1.146 0.156,0.198 10 false B 3.354,0.448 3.51,0.646 0.156,0.198 10 false B 3.938,1.104 4.094,1.302 0.156,0.198 10 false L 3.917,0.563 4.375,0.76 0.458,0.198 10 false L 2.167,0.625 2.781,0.823 0.615,0.198 10 false STOP 2.24,1.125 2.896,1.333 0.656,0.208 10 false IGN 0.406,0.417 1.344,0.615 0.938,0.198 10 false from Battery 0.25,0.927 1.198,1.313 0.948,0.385 10 false from IG2 Relay 5.865,1.094 6.323,1.292 0.458,0.198 10 false STP 5.875,0.552 6.49,0.75 0.615,0.198 10 false ST1- 5.854,1.667 6.313,1.865 0.458,0.198 10 false A61 0.063,0.052 2.188,0.333 2.125,0.281 12 false for 2AD-FHV, 2AD-FTV:

E288572E37
5.896,1.833 6.396,2.052 0.5,0.219 10 false ECM 5.583,0.99 5.896,1.229 0.313,0.24 10 false 48 5.604,0.427 5.771,0.625 0.167,0.198 10 false 10 4.135,0.979 4.302,1.177 0.167,0.198 10 false 3 4.135,0.427 4.302,0.625 0.167,0.198 10 false 5 3.177,0.313 3.344,0.51 0.167,0.198 10 false 7 3.177,0.823 3.344,1.021 0.167,0.198 10 false 6 3.177,1.156 3.344,1.354 0.167,0.198 10 false 2 2.927,1.885 4.75,2.094 1.823,0.208 10 false Stop Light Switch Assembly 2.927,1.708 3.385,1.906 0.458,0.198 10 false A77 3.354,1.292 3.813,1.49 0.458,0.198 10 false GND 3.354,0.948 3.51,1.146 0.156,0.198 10 false B 3.354,0.448 3.51,0.646 0.156,0.198 10 false B 3.938,1.104 4.094,1.302 0.156,0.198 10 false L 3.917,0.563 4.375,0.76 0.458,0.198 10 false L 2.167,0.625 2.781,0.823 0.615,0.198 10 false STOP 2.24,1.125 2.896,1.333 0.656,0.208 10 false IGN 0.406,0.417 1.344,0.615 0.938,0.198 10 false from Battery 0.25,0.927 1.198,1.313 0.948,0.385 10 false from IG2 Relay 5.865,1.094 6.323,1.292 0.458,0.198 10 false STP 5.875,0.552 6.49,0.75 0.615,0.198 10 false ST1- 5.854,1.667 6.313,1.865 0.458,0.198 10 false A62 0.073,0.052 4.479,0.292 4.406,0.24 12 false for 2WW:

E337398E06
5.479,4.875 7.063,5.271 1.583,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 2.021,1.417 4.063,1.625 2.042,0.208 10 false ECM 0.313,2.708 2.354,2.917 2.042,0.208 10 false from Battery 1.708,2.854 2.219,3.052 0.51,0.198 10 false STOP 3.698,3.615 4.208,3.813 0.51,0.198 10 false IC 2.885,4.719 5.104,4.938 2.219,0.219 10 false Stop Light Switch Assembly 2.896,4.552 3.406,4.75 0.51,0.198 10 false A77 0.656,8.427 3.656,8.656 3,0.229 10 false : CAN Communication Line 2.323,2.583 2.833,2.781 0.51,0.198 10 false 7 2.323,3.792 2.833,3.99 0.51,0.198 10 false 2 2.573,3.792 3.083,3.99 0.51,0.198 10 false GND 2.583,2.583 3.094,2.781 0.51,0.198 10 false B 4.854,2.583 5.365,2.781 0.51,0.198 10 false L 4.667,3.188 5.177,3.385 0.51,0.198 10 false ACC 4.667,3.792 5.177,3.99 0.51,0.198 10 false OUT 5.875,2.583 6.385,2.781 0.51,0.198 10 false STP2 5.875,3.177 6.385,3.375 0.51,0.198 10 false STPO 5.875,3.792 6.385,3.99 0.51,0.198 10 false STP 5.635,2.583 6.146,2.781 0.51,0.198 10 false 5 5.563,3.177 6.073,3.375 0.51,0.198 10 false 26 5.563,3.792 6.073,3.99 0.51,0.198 10 false 35 5.094,3.792 5.604,3.99 0.51,0.198 10 false 1 5.094,3.177 5.604,3.375 0.51,0.198 10 false 4 5.094,2.583 5.604,2.781 0.51,0.198 10 false 3 1.135,5.865 3.354,6.083 2.219,0.219 10 false Center Stop Light Assembly 1.135,5.698 1.646,5.896 0.51,0.198 10 false p1 1.344,5.271 1.854,5.469 0.51,0.198 10 false 1 2.448,5.271 2.958,5.469 0.51,0.198 10 false 2 2.177,5.271 2.688,5.469 0.51,0.198 10 false B 1.583,5.271 2.094,5.469 0.51,0.198 10 false E 2.99,6.583 5.583,6.792 2.594,0.208 10 false Rear Combination Light Assembly LH 2.99,6.427 3.5,6.625 0.51,0.198 10 false N13 2.99,7.885 5.583,8.094 2.594,0.208 10 false Rear Combination Light Assembly RH 2.99,7.729 3.5,7.927 0.51,0.198 10 false M19 3.458,6 3.969,6.198 0.51,0.198 10 false E 3.458,7.302 3.969,7.5 0.51,0.198 10 false E 4.052,6 4.563,6.198 0.51,0.198 10 false B 4.052,7.302 4.563,7.5 0.51,0.198 10 false B 4.271,6 4.781,6.198 0.51,0.198 10 false 1 4.271,7.302 4.781,7.5 0.51,0.198 10 false 1 3.229,6 3.74,6.198 0.51,0.198 10 false 4 3.229,7.302 3.74,7.5 0.51,0.198 10 false 4 5.49,4.729 6,4.927 0.51,0.198 10 false A80

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

·

When the entry start function does not operate, check the entry and start system (for start function)*.


*: w/ Entry and Start System



PROCEDURE

1.READ VALUE USING GTS (BRAKE CANSEL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise1 / Data List.


e.

Read the Data List according to the display on the GTS.

OK:

Display changes according to brake pedaloperation described in above table.


i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Inspection Item
Stop Light Switch 1 Stop light switch status ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Stop Light Switch 1
50003 74 25

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Inspection Item
Brake Cancel Switch Stop light switch status ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Brake Cancel Switch
50003 239 48

iii.

for 2WW:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Inspection Item
Brake Cancel Switch Stop light switch status ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Powertrain > Cruise Control > Data List
Tester Display
Brake Cancel Switch
50003 391 7


Result:
Proceed to
OK
NG



OK

2.CHECK STOP LIGHT OPERATION

NG

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)
2.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

3.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)

B

8.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL VOLTAGE)

C

3.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.
E296982C19
1.51,0.188 1.938,0.396 0.427,0.208 1.031,1.406 1.01,1.896 1.01,1.896 0.74,1.896 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.615,0.208 1.927,0.365 0.313,0.156 10 false A80 0.344,1.823 0.74,2 0.396,0.177 10 false STPO
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A80-26 (STPO) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop lights ON or OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


d.

Check the stop light switch assembly operation using the Data List and stop light operation by performing an Active Test.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay output ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light Relay
50003 105 287

Result:
Result Proceed to
When Active Test performed, Data List item not changes between ON and OFF A
When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off B



A

5.INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
5.INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


b.

Perform "Active Test" according to the display on GTS.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop lights ON or OFF Test possible at vehicle speed of 0 km/h (0 mph)
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.
E337400C01
1.5,0.219 1.917,0.469 0.417,0.25 1.75,1.167 2.167,0.5 2.167,0.5 2.333,0.5 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 1.604,0.271 1.917,0.469 0.313,0.198 10 false A77 2.417,0.417 2.833,0.625 0.417,0.208 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-4 (ACC) - Body ground Active test is OFF 11 to 14 V
A77-4 (ACC) - Body ground Active test is ON Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A77 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-35 (STP) - A77-1 (OUT) Always Below 1 Ω
A80-35 (STP) or A77-1 (OUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the A80 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A77 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A80-26 (STPO) - A77-4 (ACC) Always Below 1 Ω
A80-26 (STPO) or A77-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.
E296982C20
1.51,0.188 1.938,0.396 0.427,0.208 1.448,0.906 1.198,0.333 1.198,0.333 1.01,0.333 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.615,0.208 1.927,0.365 0.313,0.156 10 false A80 0.646,0.24 1.042,0.417 0.396,0.177 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A80-5 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8.5 to 14 V
A80-5 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STPO TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)
a.

Disconnect the stop light switch assembly connector.


b.
E270087C07
1.604,0.167 2,0.417 0.396,0.25 2.167,1.167 2.167,1.75 true 2.5,1.167 2.833,1.75 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 2.125,1.76 2.281,1.958 0.156,0.198 10 false B 2.844,1.75 3,1.948 0.156,0.198 10 false B 1.688,0.229 2.021,0.396 0.333,0.167 10 false A77
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A77-7 (B) - Body ground Always 11 to 14 V
A77-6 (B) - Body ground Ignition switch ON 11 to 14 V
A77-6 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.
E217720C22
1.5,0.167 1.917,0.417 0.417,0.25 2.521,1.802 2.354,1.802 2.354,1.802 2.354,1.052 true 2.354,0.885 2.354,0.219 2.354,0.219 2.521,0.219 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false A62 2.594,0.156 3.01,0.313 0.417,0.156 10 false STP 2.594,1.719 3.01,1.875 0.417,0.156 10 false ST1-
*a Front view of wire harness connector
(to ECM)


for 2AR-FE:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-24 (ST1-) - Body ground Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A62-11 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V



c.
E217720C23
1.5,0.167 1.917,0.417 0.417,0.25 2.833,0.448 2.677,0.448 2.677,0.448 2.281,0.896 true 2.188,0.885 2.354,0.219 2.354,0.219 2.521,0.219 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false A62 2.594,0.156 3.01,0.313 0.417,0.156 10 false STP 2.896,0.385 3.313,0.542 0.417,0.156 10 false ST1-
*a Front view of wire harness connector
(to ECM)


for 3ZR-FAE, 3ZR-FE:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-10 (ST1-) - Body ground Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A62-9 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V



d.
E207340C03
1.542,0.198 1.958,0.438 0.417,0.24 1.813,1.156 2.5,0.188 2.5,0.188 2.635,0.188 true 1.885,1.156 2.708,0.438 2.708,0.438 2.844,0.438 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.625,0.25 2.083,0.448 0.458,0.198 10 false A61 2.875,0.385 3.302,0.583 0.427,0.198 10 false STP 2.667,0.115 3.094,0.313 0.427,0.198 10 false ST1-
*a Front view of wire harness connector
(to ECM)


for 2AD-FHV, 2AD-FTV:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A61-34 (ST1-) - Body ground Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A61-35 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V



e.
E217720C24
1.5,0.167 1.917,0.417 0.417,0.25 1.979,1.875 1.781,1.875 1.781,1.875 1.417,1.292 true 2.271,0.885 2.354,0.219 2.354,0.219 2.521,0.219 true 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 1.594,0.219 2.052,0.417 0.458,0.198 10 false A62 2.031,1.823 2.448,1.979 0.417,0.156 10 false STP 2.583,0.146 3,0.302 0.417,0.156 10 false ST1-
*a Front view of wire harness connector
(to ECM)


for 2WW:

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A62-10 (ST1-) - Body ground Ignition switch ON, brake pedal depressed Below 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A62-48 (STP) - Body ground Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

11.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Temporarily replace the stop light switch assembly with a new or normally functioning one.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Clear DTCs
50002 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Clear DTCs
50002 239

iii.

for 2WW:

Powertrain > Cruise Control > Clear DTCs
50002 391


c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Trouble Codes
50001 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Trouble Codes
50001 239

iii.

for 2WW:

Powertrain > Cruise Control > Trouble Codes
50001 391


Result:
Result Proceed to
DTC is not output A
DTC P0571 is output B



A

END (STOP LIGHT SWITCH ASSEMBLY WAS DEFECTIVE)

B