Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P1578  Brake System  


DESCRIPTION

This DTC is output when the VSC system has a problem. Check the VSC system when this DTC is output.

DTC No. Detection Item DTC Detection Condition Trouble Area
P1578 Brake System
·

When the dynamic radar cruise control system is operating, the ECM receives a brake system error signal for 0.2 seconds or more.

·

When the ECM detects a malfunction in the brake system and CAN communication from the ECM to the brake system is stopped.


·

VSC system

·

Skid control ECU (brake actuator assembly)

·

ECM



CAUTION / NOTICE / HINT

HINT:

This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.


PROCEDURE

1.CHECK FOR DTCs (ABS/VSC/TRC)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK FOR DTCs

B

2.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Drive the vehicle at a speed for which dynamic radar cruise control operation is possible.

2.

Turn the cruise control system on using the cruise control switch (ON/OFF).

3.

Depress the brake pedal for 0.4 seconds or more.




e.

Enter the following menus: Powertrain / Radar Cruise1 / Trouble Codes.


f.

Check for DTCs.

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Trouble Codes
50001 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Trouble Codes
50001 239

iii.

for 2WW:

Powertrain > Cruise Control > Trouble Codes
50001 391


Result:
Result Proceed to
DTC P1578 is not output A
DTC P1578 is output B



A

B

3.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
3.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs
4.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Clear DTCs
50002 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Clear DTCs
50002 239

iii.

for 2WW:

Powertrain > Cruise Control > Clear DTCs
50002 391


e.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Drive the vehicle at a speed for which dynamic radar cruise control operation is possible.

2.

Turn the cruise control system on using the cruise control switch (ON/OFF).

3.

Depress the brake pedal for 0.4 seconds or more.




f.

Enter the following menus: Powertrain / Radar Cruise1 / Trouble Codes.


g.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Trouble Codes
50001 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Trouble Codes
50001 239

iii.

for 2WW:

Powertrain > Cruise Control > Trouble Codes
50001 391


Result:
Result Proceed to
DTC P1578 is not output A
DTC P1578 is output B



A

END

B