Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P1630  Communication Error from VSC to ECM  


DESCRIPTION

The skid control ECU (brake actuator assembly) sends signals such as cruise control cancel signals and brake demand response signals to the ECM when the dynamic radar cruise control system is operating.

DTC No. Detection Item DTC Detection Condition Trouble Area
P1630 Communication Error from VSC to ECM While the vehicle speed is 40 km/h (25 mph) or more and the dynamic radar cruise control system is operating (vehicle-to-vehicle distance control mode), if communication data from the skid control ECU (brake actuator assembly) is logically inconsistent for approximately 0.5 seconds or more.
·

Communication circuit

·

Skid control ECU (brake actuator assembly)

·

ECM



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check that the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check for the CAN communication system.

for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM

for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



Result:
Proceed to
OK
NG



OK

2.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

2.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTCs
3.CHECK FOR DTCs
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Clear DTCs
50002 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Clear DTCs
50002 239

iii.

for 2WW:

Powertrain > Cruise Control > Clear DTCs
50002 391


d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 40 km/h (25 mph) or more for 0.5 seconds or more.




e.

Enter the following menus: Powertrain / Radar Cruise1 / Trouble Codes.


f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

i.

for 2AD-FHV, 2AD-FTV:

Powertrain > Radar Cruise1 > Trouble Codes
50001 74

ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Radar Cruise1 > Trouble Codes
50001 239

iii.

for 2WW:

Powertrain > Cruise Control > Trouble Codes
50001 391


Result:
Result Proceed to
DTC P1630 is not output A
DTC P1630 is output B



A

END

B