The ECM turns on the cruise control indicator by sending indicator output demand signals to the combination meter assembly using CAN communication.
The cruise control indicator illuminates when the dynamic radar cruise control system has been turned on using the ON/OFF. If a malfunction is detected, the cruise control indicator goes out and a warning message is displayed.
The cruise control indicator circuit uses CAN communication. If the cruise control indicator is not functioning correctly, check for CAN communication system before troubleshooting this circuit.
When replacing the combination meter assembly, make sure to replace it with a new one.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Meter Display 1 | Multi-information display | OFF or All | - |
| Tester Display |
|---|
| Meter Display 1 |
The multi-information display turns on or off according to the operation of the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Enter the following menus: Powertrain / Radar Cruise1 / Data List.
Read the Data List according to the display on the GTS.
for 2AD-FHV, 2AD-FTV:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| CCS Indicator M-CPU | Cruise control indicator status | ON or OFF | ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off |
- |
| Tester Display |
|---|
| CCS Indicator M-CPU |
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Cruise Indicator | Cruise control indicator status | ON or OFF | ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off |
- |
| Tester Display |
|---|
| Cruise Indicator |
for 2WW:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| CCS Indicator M-CPU | Cruise control indicator status | ON or OFF | ON: Cruise control indicator illuminates
OFF: Cruise control indicator turns off |
- |
| Tester Display |
|---|
| CCS Indicator M-CPU |
| Result | Proceed to |
|---|---|
| The cruise control indicator illuminates and turns off according to the operation of the cruise control switch (ON/OFF). | A |
| The cruise control indicator does not illuminate but the Data List item Cruise Indicator changes according to the operation of the cruise control switch (ON/OFF). | B |
| The cruise control indicator does not illuminate and the Data List item Cruise Indicator does not change according to the operation of the cruise control switch (ON/OFF). | C |
A
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
B
C
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL