Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0050250 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

·

When the ECM detects a cruise control main switch signal, it sends it to the combination meter assembly through CAN communication. Then the cruise control indicator light turns on.

·

The cruise control indicator light circuit uses CAN communication. If there is a malfunction in this circuit, check for DTCs in the CAN communication system before troubleshooting this circuit.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

for TFT Display Type:

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
OK:

The multi-information display in the combination meter assembly turns off or completely on according to the GTS operation


for Segment Display Type:

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise indicator light (Green) OFF or ON -
Cruise Indicator Cruise indicator light (Yellow) OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Lamp Cruise
50004 122 46
OK:

Cruise control indicator light turns ON/OFF



Result:
Result Proceed to
OK A
NG B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

i.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cruise Ready Main-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch is pushed, ON or OFF changes -
Cruise Ready Sub-CPU Cruise control system standby condition ON or OFF Each time cruise control main switch is pushed, ON or OFF changes -
Cruise Indicator Cruise control indicator status ON or OFF ON: Cruise control indicator light illuminates
OFF: Cruise control indicator light turns off
-
Powertrain > Cruise Control > Data List
Tester Display
Cruise Ready Main-CPU
Cruise Ready Sub-CPU
Cruise Indicator
50003 237 109,110,114

ii.

for 2AD-FTV, 2AD-FHV:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Main SW M-CPU Cruise control switch signal (Main CPU) ON or OFF ON: Cruise control switch on
OFF: Cruise control switch off
-
CCS Indicator M-CPU Cruise control indicator light signal (Main-CPU) ON or OFF ON: Cruise control indicator light turns on
OFF: Cruise control indicator light turns off
-
Powertrain > Cruise Control > Data List
Tester Display
CCS Main SW M-CPU
CCS Indicator M-CPU
50003 76 17,13

iii.

for 2WW:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
CCS Indicator M-CPU Cruise control indicator signal (Main-CPU) ON or OFF ON: Cruise control indicator illuminated
OFF: Cruise control indicator not illuminated
-
Cruise Control Switch Cruise control switch signal ON or OFF ON: Cruise control switch (ON/OFF) pushed
OFF: Cruise control switch (ON/OFF) released
-
Powertrain > Cruise Control > Data List
Tester Display
CCS Indicator M-CPU
Cruise Control Switch
50003 391 4,8


Result:
Result Proceed to
The indicator operates normally according to the on and off operations A
The GTS screen display changes from off to on, but the cruise control indicator light in the combination meter assembly does not illuminate B
The cruise control indicator light in the combination meter assembly does not illuminate and the GTS screen display does not change from off C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C