Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0050250 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise SET Indicator Light Circuit  


DESCRIPTION

·

When the ECM detects a cruise control main switch on signal from the cruise control main switch, it sends it to the combination meter assembly through CAN communication. Then the cruise control SET indicator light turns on.

·

The cruise control SET indicator light circuit uses CAN communication. If there is a malfunction in this circuit, check for DTCs in the CAN communication system before troubleshooting this circuit.


CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

for TFT Display Type:

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display 1 Multi-information display OFF or All -
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display 1
50004 122 7
OK:

The multi-information display in the combination meter assembly turns off or completely on according to the GTS operation


for Segment Display Type:

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. SET SET indicator light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. SET
50004 122 91
OK:

Cruise control SET indicator light turns ON/OFF



Result:
Result Proceed to
OK A
NG B



A

2.READ VALUE USING GTS (SET/COAST SWITCH)

B

2.READ VALUE USING GTS (SET/COAST SWITCH)
a.

Enter the following menus: Powertrain / Cruise Control / Data List.


b.

Read the Data List according to the display on the GTS.

i.

for 2AD-FTV, 2AD-FHV:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SET/COAST Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
SET/COAST Switch
50003 76 21
OK:

When the cruise control switch (SET/COAST switch) is operated, the display changes as shown above.



ii.

for 2AR-FE, 3ZR-FE, 3ZR-FAE:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
-SET Switch -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
-SET Switch
50003 237 112
OK:

When the cruise control switch (-SET switch) is operated, the display changes as shown above.



iii.

for 2WW:

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
-SET SW -SET switch signal ON or OFF ON: -SET switch on
OFF: -SET switch off
-
Powertrain > Cruise Control > Data List
Tester Display
-SET SW
50003 391 13
OK:

When the cruise control switch (-SET switch) is operated, the display changes as shown above.




Result:
Result Proceed to
The indicator operates normally according to the on and off operations A
The GTS screen display changes from off to on, but the cruise control SET indicator light in the combination meter assembly does not illuminate B
The cruise control SET indicator light in the combination meter assembly does not illuminate, and the indication in the GTS screen display stays at OFF C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C