Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER › from 2015.10
RM3090E _53 Suspension _008765 REAR SUSPENSION _0049365 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 41651 1.INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for 4WD/AWD)

Hide 51206A 2.INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C266838C02
1.229,0.531 1.01,0.531 false 1.01,0.531 1.01,0.885 true 2.469,0.885 2.469,0.542 true 2.469,0.531 2.219,0.531 false 2.583,1.927 2.354,1.927 true 2.354,1.927 2.354,1.76 true 1.063,1.75 1.063,1.917 true 1.063,1.917 0.854,1.917 true 1.26,0.448 1.646,0.667 0.385,0.219 10 *a 2.073,0.438 2.458,0.656 0.385,0.219 10 *a 0.688,1.823 1.073,2.042 0.385,0.219 10 *a 2.635,1.844 3.021,2.063 0.385,0.219 10 *a
*a Attachment Placement Positions


Place wooden blocks or plate lift attachments on an engine lifter, and then set the rear suspension member sub-assembly so that the attachments are in the positions shown in the illustration.

NOTICE:
·

Place the wooden blocks or plate lift attachments so that the rear suspension member sub-assembly is level.

·

As the rear suspension member sub-assembly is very heavy, be sure to support it securely.




b.
C266837

Install the rear suspension member and 2 rear upper body mounting cushions with the 2 bolts and 2 nuts.

Torque:
125 N*m (1275 kgf*cm, 92 ft.*lbf)


Hide 41110 3.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (for 4WD/AWD)

Hide 37100 4.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 48790 5.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

a.

Temporarily install the upper control arm to the rear suspension member with the bolt and nut.


Hide 48770A 6.TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48740F 7.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 8.TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48258C 9.INSTALL REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 10.INSTALL REAR LOWER COIL SPRING INSULATOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48259A 11.INSTALL REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 12.INSTALL REAR UPPER COIL SPRING INSULATOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48231B 13.INSTALL REAR COIL SPRING LH

Hide 48231A 14.INSTALL REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 48540 15.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 16.TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42305 17.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

a.

Install the rear axle carrier to the rear upper control arm with the bolt and nut.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:

Since a stopper nut is used, tighten the bolt.



Hide 42304 18.INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48720A 19.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 20.TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48710B 21.CONNECT REAR TRAILING ARM ASSEMBLY LH

a.

Connect the rear trailing arm to the rear axle carrier with the 2 bolts.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 48710B 22.CONNECT REAR TRAILING ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48812 23.INSTALL REAR STABILIZER BAR

Hide 48840A 24.INSTALL REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 25.INSTALL REAR STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52296 26.INSTALL REAR SUSPENSION MEMBER BRACE LH

Hide 52295 27.INSTALL REAR SUSPENSION MEMBER BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 42450B 28.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)

Hide 42450A 29.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for 2WD)

HINT:

Use the same procedure described for the LH side.


Hide 42440 30.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD/AWD)

Hide 42410 31.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD/AWD)

HINT:

Use the same procedure described for the LH side.


Hide 32.INSTALL PARKING BRAKE ASSEMBLY

Hide 42431 33.INSTALL REAR DISC

Hide 34.CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

Hide 35.CONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 46430 36.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 46420 37.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 89516D 38.CONNECT SKID CONTROL SENSOR WIRE LH (for 2WD)

Hide 89516C 39.CONNECT SKID CONTROL SENSOR WIRE RH (for 2WD)

HINT:

Use the same procedure described for the LH side.


Hide 41.CONNECT REAR SPEED SENSOR RH (for 4WD/AWD)

HINT:

Use the same procedure described for the LH side.


Hide 42312B 42.INSTALL REAR AXLE SHAFT NUT LH (for 4WD/AWD)

Hide 42311N 43.INSTALL REAR AXLE SHAFT NUT RH (for 4WD/AWD)

HINT:

Use the same procedure described for the LH side.


Hide 48540 45.TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 46.TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48790 47.TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 48.TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48740F 49.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 50.TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48720A 51.TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 52.TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89408C 53.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)

Hide 54.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 55.INSPECT AND ADJUST REAR WHEEL ALIGNMENT