Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.10
RM3090E _51 Engine / Hybrid System _008749 CRUISE CONTROL _0226194 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch switch sends a signal to terminal D of the ECM. The ECM cancels cruise control when terminal D receives the signal.

WIRING DIAGRAM

C350504E10
6.292,3.198 6.75,3.396 0.458,0.198 10 false ECM 6.292,3.052 6.75,3.25 0.458,0.198 10 false B76 2.958,2.208 4.802,2.417 1.844,0.208 10 false A1*1, F1*2 2.938,2.385 4.781,2.594 1.844,0.208 10 false Clutch Switch Assembly 1.354,1.979 3.198,2.188 1.844,0.208 10 false EFI NO. 1 1.438,0.729 3.281,0.938 1.844,0.208 10 false from IG Circuit 0.438,2.927 2.125,3.125 1.688,0.198 10 false *1: for LHD 0.448,3.208 2.135,3.406 1.688,0.198 10 false *2: for RHD 2.854,1.677 3.01,1.875 0.156,0.198 10 false 1 4.021,1.677 4.177,1.875 0.156,0.198 10 false 2 0.094,0.063 3.521,0.323 3.427,0.26 12 false for 2AD-FTV: 5.844,1.688 6.302,1.885 0.458,0.198 10 false 73 6.125,1.813 6.583,2.01 0.458,0.198 10 false D

C350504E11
6.302,3.198 6.76,3.396 0.458,0.198 10 false ECM 6.292,3.052 6.75,3.25 0.458,0.198 10 false B77 2.958,2.208 4.802,2.417 1.844,0.208 10 false A1*1, F1*2 2.938,2.385 4.781,2.594 1.844,0.208 10 false Clutch Switch Assembly 1.292,1.969 3.135,2.177 1.844,0.208 10 false ECU-IG NO. 3 1.448,0.729 3.292,0.938 1.844,0.208 10 false from IG Circuit 0.438,2.927 2.125,3.125 1.688,0.198 10 false *1: for LHD 0.448,3.208 2.135,3.406 1.688,0.198 10 false *2: for RHD 2.854,1.677 3.01,1.875 0.156,0.198 10 false 1 4.021,1.677 4.177,1.875 0.156,0.198 10 false 2 0.052,0.031 3.479,0.292 3.427,0.26 12 false for 2AR-FE: 5.844,1.688 6.302,1.885 0.458,0.198 10 false 67 6.125,1.813 6.583,2.01 0.458,0.198 10 false D

C350504E12
6.302,3.198 6.76,3.396 0.458,0.198 10 false ECM 6.292,3.052 6.75,3.25 0.458,0.198 10 false B75 2.958,2.208 4.802,2.417 1.844,0.208 10 false A1*1, F1*2 2.938,2.385 4.781,2.594 1.844,0.208 10 false Clutch Switch Assembly 1.292,1.969 3.135,2.177 1.844,0.208 10 false ECU-IG NO. 3 1.448,0.729 3.292,0.938 1.844,0.208 10 false from IG Circuit 0.438,2.927 2.125,3.125 1.688,0.198 10 false *1: for LHD 0.448,3.208 2.135,3.406 1.688,0.198 10 false *2: for RHD 2.854,1.677 3.01,1.875 0.156,0.198 10 false 1 4.021,1.677 4.177,1.875 0.156,0.198 10 false 2 0.073,0.052 3.5,0.313 3.427,0.26 12 false for 3ZR-FE: 5.844,1.688 6.302,1.885 0.458,0.198 10 false 81 6.125,1.813 6.583,2.01 0.458,0.198 10 false D

C350504E13
6.302,3.198 6.76,3.396 0.458,0.198 10 false ECM 6.292,3.052 6.75,3.25 0.458,0.198 10 false B93 2.958,2.208 4.802,2.417 1.844,0.208 10 false A1*1, F1*2 2.938,2.385 4.781,2.594 1.844,0.208 10 false Clutch Switch Assembly 1.365,1.969 3.208,2.177 1.844,0.208 10 false EFI NO. 1 1.448,0.729 3.292,0.938 1.844,0.208 10 false from IG Circuit 0.438,2.927 2.125,3.125 1.688,0.198 10 false *1: for LHD 0.448,3.208 2.135,3.406 1.688,0.198 10 false *2: for RHD 2.854,1.677 3.01,1.875 0.156,0.198 10 false 1 4.021,1.677 4.177,1.875 0.156,0.198 10 false 2 0.094,0.073 3.521,0.333 3.427,0.26 12 false for 3ZR-FAE: 5.844,1.688 6.302,1.885 0.458,0.198 10 false 65 6.125,1.813 6.583,2.01 0.458,0.198 10 false D

C350504E14
6.302,3.198 6.76,3.396 0.458,0.198 10 false ECM 6.292,3.052 6.75,3.25 0.458,0.198 10 false A62 2.958,2.208 4.802,2.417 1.844,0.208 10 false A87*1, F1*2 2.938,2.385 4.781,2.594 1.844,0.208 10 false Clutch Switch Assembly 1.354,1.979 3.198,2.188 1.844,0.208 10 false EFI NO. 1 1.448,0.729 3.292,0.938 1.844,0.208 10 false from IG Circuit 0.438,2.927 2.125,3.125 1.688,0.198 10 false *1: for LHD 0.448,3.208 2.135,3.406 1.688,0.198 10 false *2: for RHD 2.854,1.677 3.01,1.875 0.156,0.198 10 false 1 4.021,1.677 4.177,1.875 0.156,0.198 10 false 2 0.104,0.073 3.531,0.333 3.427,0.26 12 false for 2WW: 5.844,1.688 6.302,1.885 0.458,0.198 10 false 7 6.125,1.813 6.583,2.01 0.458,0.198 10 false D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT CLUTCH SWITCH ASSEMBLY
a.

Remove the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


b.

Inspect the clutch switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM AND BATTERY)

NG

REPLACE CLUTCH SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY - ECM AND BATTERY)
a.

for 2AD-FTV

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B76 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B76-73 (D) Always Below 1 Ω
A1-2 or B76-73 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B76-73 (D) Always Below 1 Ω
F1-2 or B76-73 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




b.

for 2AR-FE

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B77 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B77-67 (D) Always Below 1 Ω
A1-2 or B77-67 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B77-67 (D) Always Below 1 Ω
F1-2 or B77-67 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




c.

for 3ZR-FE

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B75 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B75-81 (D) Always Below 1 Ω
A1-2 or B75-81 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B75-81 (D) Always Below 1 Ω
F1-2 or B75-81 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




d.

for 3ZR-FAE

i.

Disconnect the A1*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the B93 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A1-2 - B93-65 (D) Always Below 1 Ω
A1-2 or B93-65 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - B93-65 (D) Always Below 1 Ω
F1-2 or B93-65 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A1-1 - Body ground Ignition switch ON 11 to 14 V
A1-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




e.

for 2WW

i.

Disconnect the A87*1 or F1*2 clutch switch assembly connector.

*1: for LHD

*2: for RHD



ii.

Disconnect the A62 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A87-2 - A62-7 (D) Always Below 1 Ω
A87-2 or A62-7 (D) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F1-2 - A62-7 (D) Always Below 1 Ω
F1-2 or A62-7 (D) - Body ground Always 10 kΩ or higher



iv.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A87-1 - Body ground Ignition switch ON 11 to 14 V
A87-1 - Body ground Ignition switch off Below 1 V

for RHD
Tester Connection Switch Condition Specified Condition
F1-1 - Body ground Ignition switch ON 11 to 14 V
F1-1 - Body ground Ignition switch off Below 1 V




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR