There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
| Detection Item | Trouble Area |
|---|---|
|
*1: w/ Audio and Visual System (for Radio and Display Type) *2: for 4WD/AWD *3: w/ Stop and Start System *4: w/ Telematics Transceiver |
|
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω. | ·
Short between CAN bus lines ·
ECM ·
Combination meter assembly ·
Power steering ECU assembly ·
Air conditioning amplifier assembly ·
Airbag sensor assembly ·
Spiral with sensor cable sub-assembly (steering angle sensor) ·
Radio and display receiver assembly*1 ·
4WD ECU assembly*2 ·
Brake actuator assembly (skid control ECU) ·
Main body ECU (multiplex network body ECU) ·
Engine stop and start ECU*3 ·
Telematics transceiver*4 ·
No. 6 CAN junction connector ·
No. 7 CAN junction connector ·
DLC3 CAN branch wire or connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to Power Steering ECU Assembly | *d | to Brake Actuator Assembly (Skid Control ECU) |
| *e | to No. 7 CAN Junction Connector | *f | to ECM |
| *g | to DLC3 | *h | to Airbag Sensor Assembly |
| *i | to Air Conditioning Amplifier Assembly | - | - |
Disconnect the No. 6 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| G171-1 (CANH) - G171-11 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| G171-2 (CANH) - G171-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
| G171-3 (CANH) - G171-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly (skid control ECU) |
| G171-4 (CANH) - G171-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 7 CAN junction connector |
| G171-5 (CANH) - G171-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| G171-8 (CANH) - G171-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | DLC3 |
| G171-9 (CANH) - G171-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly |
| G171-10 (CANH) - G171-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 7 CAN junction connector CAN main wire) | B |
| NG (ECM CAN main wire) | C |
| NG (DLC3 CAN branch wires) | D |
| NG (ECU or sensor CAN branch wires) | E |
A
B
C
D
E
Reconnect the G171 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 7 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 7 CAN Junction Connector) |
*b | to Combination Meter Assembly |
| *c | to Telematics Transceiver (w/ Telematics Transceiver) | *d | to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type]) |
| *e | to Engine Stop and Start ECU (w/ Stop and Start System) | *f | to 4WD ECU Assembly (for 4WD/AWD) |
| *g | to No. 6 CAN Junction Connector | *h | to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
|
*1: w/ Audio and Visual System (for Radio and Display Type) *2: for 4WD/AWD *3: w/ Stop and Start System *4: w/ Telematics Transceiver |
|||
| G172-1 (CANH) - G172-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| G172-2 (CANH) - G172-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Telematics transceiver*4 |
| G172-3 (CANH) - G172-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Radio and display receiver assembly*1 |
| G172-4 (CANH) - G172-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Engine stop and start ECU*3 |
| G172-6 (CANH) - G172-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | 4WD ECU assembly*2 |
| G172-8 (CANH) - G172-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| G172-9 (CANH) - G172-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral with sensor cable sub-assembly (steering angle sensor) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 6 CAN junction connector CAN main wire) | B |
| NG (Combination meter assembly CAN main wire) | C |
| NG (ECU or sensor CAN branch wires) | D |
A
B
C
D
Reconnect the G172 No. 7 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-32 (CANH) - G16-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of DLC3 |
Reconnect the CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - G14-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G171 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *A | for 2AR-FE, 3ZR-FAE, 3ZR-FE |
| *B | for 2WW |
| *C | for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF |
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-13 (CANH) - A62-26 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-26 (CANH) - A62-25 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-7 (CANH) - A61-6 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-CCo, 2AD-DPF: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
NG