When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.
The ECM receives the brake demand signal from the driving support ECU assembly and transmits it to the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) receives a signal from the ECM and operates the skid control ECU (brake actuator assembly). The skid control ECU (brake actuator assembly) operates the brake actuator assembly and at the same time illuminates the stop light by operating the stop light control ECU assembly*1 or STOP LP relay (stop light control relay)*2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0571 | Brake Switch "A" Circuit | ·
When the ignition switch is turned ON and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more. ·
While the dynamic radar cruise control system is operating (vehicle-to-vehicle distance control mode), the ECM detects the stop light control ECU assembly error signal from the skid control ECU (brake actuator assembly) for approximately 0.2 seconds or more*1. ·
While the dynamic radar cruise control system is operating (vehicle-to-vehicle distance control mode), the ECM detects the STOP LP Relay (stop light control relay) signal from the skid control ECU (brake actuator assembly) for approximately 0.2 seconds or more*2. |
·
Stop light switch assembly ·
Stop light switch circuit ·
ECM ·
Stop light control ECU assembly*1 ·
STOP LP relay (stop light control relay)*2 ·
Stop light control ECU assembly circuit*1 ·
STOP LP relay(Stop light control relay) circuit*2 ·
Skid control ECU (brake actuator assembly) ·
ECM |
*1: for LED Type Stop Light
*2: for Bulb Type Stop Light
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.
When the entry start function does not operate, check the entry and start system (for start function)*.
*: w/ Entry and Start System
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Radar Cruise1 / Data List.
Read the Data List according to the display on the GTS.
Display changes according to brake pedaloperation described in above table.
for 2AD-FHV, 2AD-FTV:
| Tester Display | Measurement Item | Range | Normal Condition | Inspection Item |
|---|---|---|---|---|
| Stop Light Switch 1 | Stop light switch status | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light Switch 1 |
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
| Tester Display | Measurement Item | Range | Normal Condition | Inspection Item |
|---|---|---|---|---|
| Brake Cancel Switch | Stop light switch status | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Brake Cancel Switch |
for 2WW:
| Tester Display | Measurement Item | Range | Normal Condition | Inspection Item |
|---|---|---|---|---|
| Brake Cancel Switch | Stop light switch status | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Brake Cancel Switch |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | On |
| Brake pedal released | Off |
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-26 (STPO) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform "Active Test" according to the display on GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop lights | ON or OFF | Test possible at vehicle speed of 0 km/h (0 mph) |
| Tester Display |
|---|
| Stop Light Relay |
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Check the stop light switch assembly operation using the Data List and stop light operation by performing an Active Test.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Relay Output | Stop light control relay output | ON or OFF | ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off) |
- |
| Tester Display |
|---|
| Stop Light Relay |
| Result | Proceed to |
|---|---|
| When Active Test performed, Data List item not changes between ON and OFF | A |
| When Active Test performed, Data List item changes between ON and OFF and stop lights turn on and off | B |
A
B
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform "Active Test" according to the display on GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop lights | ON or OFF | Test possible at vehicle speed of 0 km/h (0 mph) |
| Tester Display |
|---|
| Stop Light Relay |
| *a | Component with harness connected
(Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A77-4 (ACC) - Body ground | Active test is OFF | 11 to 14 V |
| A77-4 (ACC) - Body ground | Active test is ON | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A100 skid control ECU (brake actuator assembly) connector.
Disconnect the A77 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-35 (STP) - A77-1 (OUT) | Always | Below 1 Ω |
| A100-35 (STP) or A77-1 (OUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A100 skid control ECU (brake actuator assembly) connector.
Disconnect the A77 stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A100-26 (STPO) - A77-4 (ACC) | Always | Below 1 Ω |
| A100-26 (STPO) or A77-4 (ACC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A100-5 (STP2) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8.5 to 14 V |
| A100-5 (STP2) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the stop light switch assembly connector.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A77-7 (B) - Body ground | Always | 11 to 14 V |
| A77-6 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| A77-6 (B) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
for 2AR-FE:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-24 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| A62-11 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to ECM) |
for 3ZR-FAE, 3ZR-FE:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-10 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| A62-9 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to ECM) |
for 2AD-FHV, 2AD-FTV:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-34 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| A61-35 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to ECM) |
for 2WW:
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-10 (ST1-) - Body ground | Ignition switch ON, brake pedal depressed | Below 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |
| A62-48 (STP) - Body ground | Brake pedal depressed | 7.5 to 14 V |
| Brake pedal released | Below 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the stop light switch assembly with a new or normally functioning one.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
for 2AD-FHV, 2AD-FTV:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
for 2WW:
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST
for 2AD-FHV, 2AD-FTV:
for 2AR-FE, 3ZR-FE, 3ZR-FAE:
for 2WW:
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0571 is output | B |
A
B
for 2AD-FHV: Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV: Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AR-FE: Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 2WW: Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL