Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER (for LHD)
RM3620E _52 Drivetrain _076045 CLUTCH _0370083 CLUTCH MASTER CYLINDER(for LHD) A

CLUTCH  CLUTCH MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 31415 1.INSTALL CLUTCH MASTER CYLINDER GASKET

C408265

a.

Install a new clutch master cylinder gasket to the clutch master cylinder assembly.


Hide 31410 2.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.
C408263

Install the clutch master cylinder assembly.


Hide 31481 3.TEMPORARILY INSTALL CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.
C403558

Temporarily install the clutch master cylinder to flexible hose tube to the clutch master cylinder.


Hide 4.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY

Hide 31453A 5.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

Hide 31481 6.TIGHTEN CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.
C403560C01
1.531,2.313 1.844,2.51 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the clutch master cylinder to flexible hose tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31434E 7.CONNECT NO. 1 CLUTCH RESERVOIR HOSE

a.
C403557

Connect the No. 1 clutch reservoir hose to the clutch master cylinder assembly, and slide the hose clip to secure it.

NOTICE:
C408551C01
1.5,2.26 1.25,2.26 1.25,2.26 1.49,1.656 true 2.708,3.094 2.25,3.208 2.25,3.208 1.802,3.083 true 1.313,2.969 1.063,2.969 1.063,2.969 0.781,3.427 true 2.708,4.24 2.25,4.354 2.25,4.354 1.802,4.229 true 0.719,2.938 1.031,3.094 0.313,0.156 10 false *a 1.354,2.906 1.667,3.063 0.313,0.156 10 false *b 2.365,1.802 2.844,2.063 0.479,0.26 10 true *c 2.156,2.354 2.469,2.51 0.313,0.156 10 false *d 2.146,3.563 2.458,3.719 0.313,0.156 10 false *e 2.188,3.219 2.5,3.375 0.313,0.156 10 false *b 1.552,2.167 1.865,2.323 0.313,0.156 10 false *b 2.177,4.375 2.49,4.531 0.313,0.156 10 false *b
*a Top of Vehicle
*b Paint Mark
*c 0 to 2 mm (0 to 0.0787 in.)
*d OK
*e NG


·

Make sure that the paint mark of the No. 1 clutch reservoir hose is within the location shown in the illustration.

·

Make sure that the claws of the hose clip are within the location shown in the illustration.

·

Connect the No. 1 clutch reservoir hose so that it will not be twisted.

·

Face the blue mark upward.




Hide 10.BLEED CLUTCH PIPE LINE

Hide 11.INSPECT FOR BRAKE FLUID LEAK

HINT:
·

Check for leakage in the brake system.

·

Check for leakage in the clutch system.



Hide 12.CHECK FLUID LEVEL IN RESERVOIR

Hide 31301 13.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY