Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM3620E _57 Power Source / Network _076016 NETWORKING _0371251 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the doors is detected consecutively 3 times.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2325 LIN Communication Bus Malfunction The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH

·

Rear power window regulator motor assembly RH

·

Double lock door control relay assembly (w/ Double Looking System)

·

Sliding roof drive gear sub-assembly (w/ Sliding Roof System)

·

Sliding roof drive gear assembly (w/ Panoramic Moon Roof System)

·

Kick door control sensor (w/ Hands Free Power Back Door)

·

Harness or connector



WIRING DIAGRAM

C407696E01
1.552,5.333 1.792,5.552 0.24,0.219 10 false LIN 1.49,3.823 1.865,4.021 0.375,0.198 10 false LIN2 5.427,2.667 5.813,2.875 0.385,0.208 10 false LIN2 1.563,6.792 1.802,7.01 0.24,0.219 10 false LIN 5.396,6.792 5.969,7.135 0.573,0.344 10 false LIN 5.417,5.375 5.656,5.594 0.24,0.219 10 false LIN 5.271,3.885 6.438,4.573 1.167,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 4.104,3.615 5.177,4.219 1.073,0.604 10 false Instrument Panel Junction Block Assembly 4.969,5.792 6.906,6.229 1.938,0.438 10 false Front Power Window Regulator Motor Assembly RH 0.375,4.156 1.958,4.646 1.583,0.49 10 false Multiplex Network Master Switch Assembly 0.354,5.802 2.281,6.208 1.927,0.406 10 false Front Power Window Regulator Motor Assembly LH 4.865,7.271 6.802,7.76 1.938,0.49 10 false Rear Power Window Regulator Motor Assembly RH 0.365,7.219 2.302,7.688 1.938,0.469 10 false Rear Power Window Regulator Motor Assembly LH 1.479,3.5 1.823,3.719 0.344,0.219 10 false LIN1 0.615,8.344 2.542,8.646 1.927,0.302 10 false : LIN Communication Line 0.406,3.969 0.844,4.219 0.438,0.25 10 false J2 4.979,5.625 5.594,5.938 0.615,0.313 10 false I7 4.854,7.083 5.771,7.354 0.917,0.271 10 false K5 0.365,7.052 0.802,7.302 0.438,0.25 10 false L5 0.344,5.615 0.781,5.865 0.438,0.25 10 false J6 5.292,3.708 5.729,3.958 0.438,0.25 10 false A 4.031,2.677 4.469,2.927 0.438,0.25 10 false 4N 5.135,2.5 5.573,2.75 0.438,0.25 10 false 16 4,2.49 4.438,2.74 0.438,0.25 10 false 25*6 1.875,3.344 2.313,3.594 0.438,0.25 10 false 17 5.198,5.146 5.635,5.396 0.438,0.25 10 false 9 5.156,3.083 5.594,3.333 0.438,0.25 10 false 11 1.885,5.156 2.323,5.406 0.438,0.25 10 false 9 1.865,6.615 2.302,6.865 0.438,0.25 10 false 9 5.219,6.646 5.656,6.896 0.438,0.25 10 false 9 4.052,3.219 4.49,3.469 0.438,0.25 10 false 4D 4.083,3 4.521,3.25 0.438,0.25 10 false 3 5.396,3.24 5.833,3.49 0.438,0.25 10 false GND1 1.865,3.677 2.302,3.927 0.438,0.25 10 false 16 0.063,0.104 0.875,0.542 0.813,0.438 12 false for LHD: 2.281,7.604 4.208,7.823 1.927,0.219 10 false *1: w/ Sliding Roof System 4.042,2.052 4.479,2.302 0.438,0.25 10 false 4D 4.042,1.854 4.479,2.104 0.438,0.25 10 false 17 0.615,0.729 1.052,0.979 0.438,0.25 10 false P4 0.594,0.885 3.469,1.479 2.875,0.594 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)*1, Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*2 1.406,2.073 1.844,2.323 0.438,0.25 10 false MPX1 1.927,1.875 2.365,2.125 0.438,0.25 10 false 9 0.406,2.292 0.844,2.542 0.438,0.25 10 false A28 1.646,0.479 2.083,0.729 0.438,0.25 10 false MPX1 2.115,0.333 2.552,0.583 0.438,0.25 10 false 7 0.406,2.458 2.01,2.802 1.604,0.344 10 false Double Lock Door Control Relay Assembly*3 2.271,8.198 4.521,8.448 2.25,0.25 10 false *3: w/ Double Locking System 2.281,7.906 4.76,8.177 2.479,0.271 10 false *2: w/ Panoramic Moon Roof System 4.365,0.74 4.802,0.99 0.438,0.25 10 false Q7 4.323,0.927 6.385,1.323 2.063,0.396 10 false Kick Door Control Sensor*4 4.781,0.479 5.219,0.729 0.438,0.25 10 false LIN 4.573,0.302 5.01,0.552 0.438,0.25 10 false 6 2.292,8.5 4.667,8.76 2.375,0.26 10 false *4: w/ Hands Free Power Back Door 4.625,8.188 6.875,8.438 2.25,0.25 10 false *5: except Manual Transaxle 4.625,8.49 6.875,8.74 2.25,0.25 10 false *6: for Manual Transaxle 3.708,2.677 4.146,2.927 0.438,0.25 10 false 4H 3.656,2.49 4.094,2.74 0.438,0.25 10 false 25*5

C407697E02
1.552,5.333 1.792,5.552 0.24,0.219 10 false LIN 5.438,3.833 5.813,4.031 0.375,0.198 10 false LIN2 1.479,2.677 1.865,2.885 0.385,0.208 10 false LIN2 1.563,6.792 1.802,7.01 0.24,0.219 10 false LIN 5.396,6.792 5.969,7.135 0.573,0.344 10 false LIN 5.417,5.375 5.656,5.594 0.24,0.219 10 false LIN 0.396,3.771 1.563,4.458 1.167,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 1.833,3.615 2.906,4.302 1.073,0.688 10 false Instrument Panel Junction Block Assembly 4.969,5.792 6.906,6.229 1.938,0.438 10 false Front Power Window Regulator Motor Assembly RH 4.906,4.188 6.49,4.677 1.583,0.49 10 false Multiplex Network Master Switch Assembly 0.354,5.802 2.281,6.208 1.927,0.406 10 false Front Power Window Regulator Motor Assembly LH 4.865,7.271 6.781,7.76 1.917,0.49 10 false Rear Power Window Regulator Motor Assembly RH 0.365,7.219 2.302,7.688 1.938,0.469 10 false Rear Power Window Regulator Motor Assembly LH 5.406,3.49 5.75,3.708 0.344,0.219 10 false LIN1 0.615,8.344 2.542,8.646 1.927,0.302 10 false : LIN Communication Line 4.906,4.031 5.344,4.281 0.438,0.25 10 false I2 4.979,5.625 5.594,5.938 0.615,0.313 10 false I7 4.854,7.083 5.771,7.354 0.917,0.271 10 false K5 0.365,7.052 0.802,7.302 0.438,0.25 10 false L5 0.344,5.615 0.781,5.865 0.438,0.25 10 false J6 0.406,3.604 0.844,3.854 0.438,0.25 10 false A 2.906,2.677 3.344,2.927 0.438,0.25 10 false 4H 1.875,2.51 2.313,2.76 0.438,0.25 10 false 16 2.906,2.479 3.344,2.729 0.438,0.25 10 false 25 5.104,3.344 5.542,3.594 0.438,0.25 10 false 17 5.198,5.146 5.635,5.396 0.438,0.25 10 false 9 1.854,3.094 2.292,3.344 0.438,0.25 10 false 11 1.885,5.156 2.323,5.406 0.438,0.25 10 false 9 1.865,6.615 2.302,6.865 0.438,0.25 10 false 9 5.219,6.646 5.656,6.896 0.438,0.25 10 false 9 2.927,3.208 3.365,3.458 0.438,0.25 10 false 4D 2.979,3.031 3.417,3.281 0.438,0.25 10 false 3 1.406,3.219 1.844,3.469 0.438,0.25 10 false GND1 5.094,3.677 5.531,3.927 0.438,0.25 10 false 16 0.063,0.104 0.875,0.542 0.813,0.438 12 false for RHD: 2.281,8.365 4.781,8.625 2.5,0.26 10 false *2: w/ Panoramic Moon Roof System 2.938,2.063 3.375,2.313 0.438,0.25 10 false 4D 2.927,1.854 3.365,2.104 0.438,0.25 10 false 17 3.781,0.698 4.219,0.948 0.438,0.25 10 false P4 3.74,0.875 6.719,1.396 2.979,0.521 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly)*1, Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*2 5.385,2.073 5.823,2.323 0.438,0.25 10 false MPX1 3.938,0.302 4.375,0.552 0.438,0.25 10 false 7 4.927,2.323 5.365,2.573 0.438,0.25 10 false A28 4.188,0.479 4.625,0.729 0.438,0.25 10 false MPX1 5.177,1.885 5.615,2.135 0.438,0.25 10 false 9 4.938,2.469 6.542,2.813 1.604,0.344 10 false Double Lock Door Control Relay Assembly*3 4.635,8.073 6.948,8.323 2.313,0.25 10 false *3: w/ Double Locking System 2.313,8.073 4.813,8.333 2.5,0.26 10 false *1: w/ Sliding Roof System 1.531,0.49 1.969,0.74 0.438,0.25 10 false LIN 1.896,0.333 2.333,0.583 0.438,0.25 10 false 6 0.438,0.708 0.875,0.958 0.438,0.25 10 false Q7 0.438,0.896 3.417,1.417 2.979,0.521 10 false Kick Door Control Sensor*4 4.615,8.375 6.927,8.646 2.313,0.271 10 false *4: w/ Hands Free Power Back Door

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5 seconds intervals until communication between the GTS and vehicle begins.

·

When the front power window regulator motor assembly LH*1 or RH*2 is removed and reinstalled or replaced, the front power window regulator motor assembly LH*1 or RH*2 must be initialized.

*1: for LHD

*2: for RHD


·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

b.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is not output A
DTC B2325 is output (for LHD) B
DTC B2325 is output (for RHD) C



A

B

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

6.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the J6 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2321 is output B



A

3.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

3.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the J2 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B1206 and B2321 are output B



A

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the I7 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Hands Free Power Back Door) A
DTC B2325 is output (w/o Hands Free Power Back Door) B
DTC B2322 is output C



A

11.CHECK KICK DOOR CONTROL SENSOR

B

12.CHECK FOR VEHICLE TYPE

C

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J2 multiplex network master switch assembly connector.


b.

Disconnect the J6 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-16 (LIN2) - J6-9 (LIN) Always Below 1 Ω
J2-16 (LIN2) or J6-9 (LIN) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the I7 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2321 is output B



A

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

7.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the I2 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B1206 and B2321 are output B



A

8.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

19.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
8.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the J6 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2322 is output B



A

9.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

9.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the K5 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2323 is output B



A

10.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

10.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the L5 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Hands Free Power Back Door) A
DTC B2325 is output (w/o Hands Free Power Back Door) B
DTC B2324 is output C



A

11.CHECK KICK DOOR CONTROL SENSOR

B

12.CHECK FOR VEHICLE TYPE

C

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

11.CHECK KICK DOOR CONTROL SENSOR
a.

Disconnect the Q7 kick door control sensor connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B2325 is not output B



A

12.CHECK FOR VEHICLE TYPE

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

12.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle type with Sliding Roof System A
Vehicle type with Panoramic Moon Roof System B
Vehicle type without Sliding Roof System and Panoramic Moon Roof System C



A

13.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

B

18.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

C

14.CHECK FOR VEHICLE TYPE
13.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Disconnect the P4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B1273 is output B



A

14.CHECK FOR VEHICLE TYPE

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

14.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle type with Double Locking System A
Vehicle type without Double Locking System B



A

15.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

B

16.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
15.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Disconnect the A28 double lock door control relay assembly connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output A
DTC B1249 is output B



A

16.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Disconnect the J6 front power window regulator motor assembly LH connector.


d.

Disconnect the I7 front power window regulator motor assembly RH connector.


e.

Disconnect the L5 rear power window regulator motor assembly LH connector.


f.

Disconnect the K5 rear power window regulator motor assembly RH connector.


g.

w/ Sliding Roof System:

i.

Disconnect the P4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.



h.

w/ Panoramic Moon Roof System:

i.

Disconnect the P4 sliding roof ECU (sliding roof drive gear assembly) connector.



i.

w/ Double Locking System:

i.

Disconnect the A28 double lock door control relay assembly connector.



j.

w/ Hands Free Power Back Door:

i.

Disconnect the Q7 kick door control sensor connector.



k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - Body ground Always 10 kΩ or higher
A-16 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

17.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
17.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)
a.

for LHD without Manual Transaxle, RHD:

i.

Disconnect the 4D and 4H instrument panel junction block assembly connectors.



b.

for LHD with Manual Transaxle:

i.

Disconnect the 4D and 4N instrument panel junction block assembly connectors.



c.

Disconnect the J6 front power window regulator motor assembly LH connector.


d.

Disconnect the I7 front power window regulator motor assembly RH connector.


e.

Disconnect the L5 rear power window regulator motor assembly LH connector.


f.

Disconnect the K5 rear power window regulator motor assembly RH connector.


g.

w/ Sliding Roof System:

i.

Disconnect the P4 sliding roof ECU (sliding roof drive gear sub-assembly) connector.



h.

w/ Panoramic Moon Roof System:

i.

Disconnect the P4 sliding roof ECU (sliding roof drive gear assembly) connector.



i.

w/ Double Locking System:

i.

Disconnect the A28 double lock door control relay assembly connector.



j.

w/ Hands Free Power Back Door:

i.

Disconnect the Q7 kick door control sensor connector.



k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

*1: w/ Sliding Roof System, Panoramic Moon Roof System, Hands Free Power Back Door or Double Locking System

*2: for LHD without Manual Transaxle, RHD

*3: for LHD with Manual Transaxle

4D-17 - Body ground*1 Always 10 kΩ or higher
4H-25 - Body ground*2 Always 10 kΩ or higher
4N-25 - Body ground*3 Always 10 kΩ or higher
4D-17 - Other terminals*1 Always 10 kΩ or higher
4H-25 - Other terminals*2 Always 10 kΩ or higher
4N-25 - Other terminals*3 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Disconnect the P4 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Clear the DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2325 is output (w/ Double Locking System) A
DTC B2325 is output (w/o Double Locking System) B
DTC B1273 is output C



A

15.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

B

16.CHECK HARNESS AND CONNECTOR (LIN Bus Circuit)

C

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

19.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the I2 multiplex network master switch assembly connector.


b.

Disconnect the I7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I2-16 (LIN2) - I7-9 (LIN) Always Below 1 Ω
I2-16 (LIN2) or I7-9 (LIN) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR