Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2018.10–2019.02
RM3620E _51 Engine / Hybrid System _076333 HYBRID / BATTERY CONTROL _0371639 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  INSTALLATION  


PROCEDURE

Hide 821H1 1.INSTALL HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A443809

Insert the HV floor under wire into the floor panel hole and engage the grommet.


b.
A443808

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.
A443810

Install new 2 stud clamps.


d.

Install the 3 bolts and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
A431274

Install new 2 stud clamps.


f.

Install the bolt and 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
A433711

Install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.
A433710

Connect the engine room main wire to the vehicle body with the nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.
A435098C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and 2 claws to install the No. 1 terminal cap.


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 5.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the vehicle body with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 58723E 6.INSTALL ENGINE SERVICE COVER CUSHION

a.
A431006

Install the engine service cover cushion with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 58724F 7.INSTALL NO. 2 ENGINE SERVICE COVER CUSHION

a.
A431005

Install the No. 2 engine service cover cushion with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 58151 8.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.
A432104

Install the front No. 1 floor heat insulator with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 58152A 9.INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR

a.
A431580C01
0,0 0,0 false

Install the front lower No. 1 floor heat insulator with the nut and bolt.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


b.

Install the clip.


Hide 58153E 10.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR

a.
A431004C01
0,0 0,0 false

Install the front No. 2 floor heat insulator with the 2 nuts.

Torque:
4.9 N*m (50 kgf*cm, 43 in.*lbf)


b.

Install the clip.


Hide 58167A 11.INSTALL FRONT CENTER FLOOR COVER

a.
A435677

Install the front center floor cover with the 2 clips.


Hide 51468B 14.INSTALL ENGINE UNDER COVER HEAT INSULATOR

Hide 51420 15.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51441 16.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53895B 17.INSTALL FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 18.INSTALL FRONT FENDER FRONT SPLASH SHIELD LH

Hide 19.INSTALL FRONT WHEELS

Hide 821H1 20.CONNECT HV FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.
A430746

Engage the clamp.


b.
A430745

Install the HV under floor wire with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


c.

Engage the clamp.


d.
A430744

Engage the 3 claws to install the No. 4 relay block cover.


e.

Connect the shield ground to the HV battery.


f.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide 71033 22.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide 58464D 23.INSTALL BATTERY SERVICE COVER BOARD

Hide 58466J 24.INSTALL NO. 2 BATTERY SERVICE COVER BOARD

Hide 67918E 25.INSTALL REAR DOOR SCUFF PLATE LH

Hide 58467H 26.INSTALL NO. 3 BATTERY SERVICE COVER BOARD

Hide 67917C 27.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 28.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 29.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 82111 31.CONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.


NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.


a.

Connect the inverter with converter assembly connector and move the lock lever to lock them.

NOTICE:
·

Do not touch the waterproof seal or terminals of the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.

·

Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.