Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2018.10–2019.09
RM3620E _58 Vehicle Interior _076050 LIGHTING (INT) _0371654 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Map light assembly

·

No. 1 room light assembly

·

Transponder key coil*1

·

No. 1 interior illumination light assembly (footwell light)*2

·

No. 2 interior illumination light assembly (footwell light)*2

·

No. 3 interior illumination light assembly (center tray light)*3

·

No. 4 interior illumination light assembly (driver side tray light)*3

·

No. 5 interior illumination light assembly (front passenger side tray light)*3

·

No. 6 interior illumination light assembly (cup holder light)*4

*1: w/o Entry and Start System

*2: w/ Footwell Light

*3: w/ Tray Light

*4: w/ Cup Holder Light



WIRING DIAGRAM

E407698E01
1.719,4.052 4.625,4.25 2.906,0.198 10 false No. 1 Room Light Assembly 1.063,0.115 4.427,0.313 3.365,0.198 10 false from Auxiliary Battery 0.333,0.271 0.948,0.469 0.615,0.198 10 false DOME 5.698,1.146 6.156,1.344 0.458,0.198 10 false ILE 5.448,0.844 5.604,1.042 0.156,0.198 10 false 1 5.531,7.427 5.688,7.625 0.156,0.198 10 false A 5.49,7.615 7.135,8.052 1.646,0.438 10 false Main Body ECU (Multiplex Network Body ECU) 4.208,7.604 5.271,8.198 1.063,0.594 10 false Instrument Panel Junction Block Assembly 1.417,6.813 4.323,7.01 2.906,0.198 10 false Map Light Assembly 1.906,1.74 4.969,1.938 3.063,0.198 10 false Transponder Key Coil* 0.104,8.396 3.167,8.594 3.063,0.198 10 false *: w/o Entry and Start System 0.469,1.438 1.531,1.813 1.063,0.375 10 false from DOME CUT Relay 4.385,1.031 4.698,1.229 0.313,0.198 10 false 4D 4.375,0.823 4.688,1.021 0.313,0.198 10 false 29 1.917,1.583 2.229,1.781 0.313,0.198 10 false G53 2.896,1.167 3.51,1.365 0.615,0.198 10 false ILL- 1.906,1.167 2.521,1.365 0.615,0.198 10 false ILL+ 1.688,0.896 1.844,1.094 0.156,0.198 10 false 2 3.271,0.896 3.427,1.094 0.156,0.198 10 false 4 1.438,2.958 1.594,3.156 0.156,0.198 10 false 1 1.667,3.229 1.823,3.427 0.156,0.198 10 false B 3.188,2.667 3.646,2.865 0.458,0.198 10 false CTY 3.354,3.51 3.51,3.708 0.156,0.198 10 false E 3.667,2.667 3.823,2.865 0.156,0.198 10 false 3 3.646,3.24 3.802,3.438 0.156,0.198 10 false 2 1.719,3.865 2.031,4.063 0.313,0.198 10 false P15 0.781,5.167 1.24,5.365 0.458,0.198 10 false +B1 0.479,4.885 0.792,5.083 0.313,0.198 10 false 10 3.365,4.74 3.823,4.938 0.458,0.198 10 false CTY 3.375,6.24 3.833,6.438 0.458,0.198 10 false GND 3.865,6 4.177,6.198 0.313,0.198 10 false 11 3.865,4.729 4.021,4.927 0.156,0.198 10 false 1 1.427,6.625 1.74,6.823 0.313,0.198 10 false P14 2.635,2.615 3.094,2.813 0.458,0.198 10 false OFF 2,4.667 2.458,4.865 0.458,0.198 10 false OFF 1.979,5.625 2.438,5.823 0.458,0.198 10 false OFF 2.865,5.042 3.323,5.24 0.458,0.198 10 false DOOR 3.063,3.073 3.521,3.271 0.458,0.198 10 false DOOR 2.688,3.531 3,3.729 0.313,0.198 10 false ON 1.99,5.333 2.302,5.531 0.313,0.198 10 false ON 1.979,6.271 2.292,6.469 0.313,0.198 10 false ON

E407699E02
0.677,0.656 1.292,0.854 0.615,0.198 10 false DOME 1.458,0.49 4.823,0.688 3.365,0.198 10 false from Auxiliary Battery 5.427,5.292 5.583,5.49 0.156,0.198 10 false A 5.438,5.479 7.094,5.875 1.656,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.406,4.146 5.469,4.76 1.063,0.615 10 false Instrument Panel Junction Block Assembly 0.99,2.115 3.063,2.479 2.073,0.365 10 false No. 1 Illumination Light Assembly (Footwell Light)*1 1.021,4.063 3.094,4.427 2.073,0.365 10 false No. 2 Illumination Light Assembly (Footwell Light)*1 1.094,6 3.167,6.365 2.073,0.365 10 false No. 6 Illumination Light Assembly (Cup Holder Light)*2 0.104,7.75 2.104,8.021 2,0.271 10 false *1: w/ Footwell Light 0.104,8.094 2.104,8.365 2,0.271 10 false *2: w/ Cup Holder Light 5.688,1.521 6.302,1.719 0.615,0.198 10 false FSPT 4.385,1.385 4.698,1.583 0.313,0.198 10 false 4A 4.375,3.333 4.688,3.531 0.313,0.198 10 false 4A 1.438,1.521 1.594,1.719 0.156,0.198 10 false B 1.438,3.448 1.594,3.646 0.156,0.198 10 false B 1.448,5.385 1.604,5.583 0.156,0.198 10 false B 2.51,1.531 2.667,1.729 0.156,0.198 10 false L 2.521,3.448 2.677,3.646 0.156,0.198 10 false L 2.542,5.375 2.698,5.573 0.156,0.198 10 false L 1.208,1.271 1.365,1.469 0.156,0.198 10 false 2 1.219,3.208 1.375,3.406 0.156,0.198 10 false 2 1.219,5.135 1.375,5.333 0.156,0.198 10 false 2 2.813,5.146 2.969,5.344 0.156,0.198 10 false 1 2.802,3.219 2.958,3.417 0.156,0.198 10 false 1 2.833,1.271 2.99,1.469 0.156,0.198 10 false 1 4.375,1.188 4.688,1.385 0.313,0.198 10 false 37 4.385,3.115 4.698,3.313 0.313,0.198 10 false 36 5.375,1.271 5.688,1.469 0.313,0.198 10 false 26 0.99,1.948 1.448,2.146 0.458,0.198 10 false G77 1.031,3.885 1.49,4.083 0.458,0.198 10 false G76 1.083,5.813 1.542,6.01 0.458,0.198 10 false N48

E407700E01
1.052,1.552 3.125,1.938 2.073,0.385 10 false No. 3 Illumination Light Assembly (Center Tray Light)* 1.073,3.5 3.146,3.885 2.073,0.385 10 false No. 4 Illumination Light Assembly (Driver Side Tray Light)* 0.896,5.385 3.365,5.75 2.469,0.365 10 false No. 5 Illumination Light Assembly (Front Passenger Side Tray Light)* 0.125,6.198 2.594,6.563 2.469,0.365 10 false *: w/ Tray Light 1.427,0.906 1.583,1.104 0.156,0.198 10 false B 1.427,2.854 1.583,3.052 0.156,0.198 10 false B 1.458,4.781 1.615,4.979 0.156,0.198 10 false B 2.542,0.896 2.698,1.094 0.156,0.198 10 false E 2.531,2.875 2.688,3.073 0.156,0.198 10 false E 2.5,4.792 2.656,4.99 0.156,0.198 10 false E 1.052,1.365 1.51,1.563 0.458,0.198 10 false G87 1.094,3.313 1.552,3.51 0.458,0.198 10 false G86 0.917,5.198 1.375,5.396 0.458,0.198 10 false H3 1.198,0.677 1.354,0.875 0.156,0.198 10 false 2 1.208,2.594 1.365,2.792 0.156,0.198 10 false 2 1.198,4.531 1.354,4.729 0.156,0.198 10 false 2 2.802,0.656 2.958,0.854 0.156,0.198 10 false 1 2.813,2.615 2.969,2.813 0.156,0.198 10 false 1 2.854,4.542 3.01,4.74 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Entry and Start System:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.



PROCEDURE

1.CHECK INTERIOR LIGHT
a.

Check which interior illumination does not turn on.


Result:
Result Proceed to
Map light assembly, No. 1 room light assembly or transponder key coil (w/o Entry and Start System) does not turn on A
Interior foot illumination (w/ Footwell Light), tray illumination (w/ Tray Light) or cup holder illumination (w/ Cup Holder Light) does not turn on B



A

2.PERFORM ACTIVE TEST USING GTS

B

5.PERFORM ACTIVE TEST USING GTS
2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system* OFF or ON Perform the Active Test with the DOOR switch in the map light assembly, No. 1 room light assembly and transponder key coil (w/o Entry and Start System) turned on.
Body Electrical > Main Body > Active Test
Tester Display
Illuminated Entry System
50004 123 4

*: Refer to Operation Check for the lights that are controlled by the illuminated entry system.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK


OK:

Map light assembly, No. 1 room light assembly and transponder key coil (w/o Entry and Start System) turn on or off.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the P14 map light assembly connector.


b.

Disconnect the P15 No. 1 room light assembly connector.


c.

Disconnect the G53 transponder key coil connector.*

*: w/o Entry and Start System



d.

Disconnect the 4D instrument panel junction block assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P14-1 (CTY) - 4D-29 Always Below 1 Ω
P14-1 (CTY) or 4D-29 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E364134C10
4.802,0.396 5.385,0.625 0.583,0.229 1.5,0.177 2.083,0.406 0.583,0.229 3.677,1.042 4.042,1.438 4.042,1.438 4.219,1.438 true 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.698,0.188 2.198,0.427 0.5,0.24 10 false 4D 5.042,0.427 5.542,0.667 0.5,0.24 10 false A 4.271,1.354 4.771,1.594 0.5,0.24 10 false ILE
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-29 - A-1 (ILE) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fr Foot Light Operation of the following lights:
·

No. 1 interior illumination light assembly (footwell light)

·

No. 2 interior illumination light assembly (footwell light)

·

No. 3 interior illumination light assembly (center tray light)*1

·

No. 4 interior illumination light assembly (driver side tray light)*1

·

No. 5 interior illumination light assembly (front passenger side tray light)*1

·

No. 6 interior illumination light assembly (cup holder light)*2


OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Fr Foot Light
50004 123 11

*1: w/ Tray Light

*2: w/ Cup Holder Light


OK:

Connected light is turn on or off.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY [FOOTWELL LIGHT] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY [FOOTWELL LIGHT] - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

*1: w/ Tray Light

*2: w/ Cup Holder Light


a.

Disconnect the G77 No. 1 interior illumination light assembly (footwell light) connector.


b.

Disconnect the G76 No. 2 interior illumination light assembly (footwell light) connector.


c.

Disconnect the G87 No. 3 interior illumination light assembly (center tray light) connector.*1


d.

Disconnect the G86 No. 4 interior illumination light assembly (driver side light) connector.*1


e.

Disconnect the H3 No. 5 interior illumination light assembly (front passenger light) connector.*1


f.

Disconnect the N48 No. 6 interior illumination light assembly (cup holder light) connector.*2


g.

Disconnect the 4A instrument panel junction block assembly connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-37 - G77-1 (L) Always Below 1 Ω
4A-37 or G77-1 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E361166C22
1.458,0.271 1.979,0.479 0.521,0.208 5.01,0.354 5.531,0.563 0.521,0.208 6.448,1.5 6.333,1.5 6.333,1.5 6.115,1.094 true 0.229,0.115 0.542,0.271 0.313,0.156 10 false *a 5.219,0.375 5.375,0.531 0.156,0.156 10 false A 1.646,0.292 1.917,0.479 0.271,0.188 10 false 4A 6.51,1.417 7.052,1.698 0.542,0.281 10 false FSPT
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4A-37 - A-26 (FSPT) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY