Home › Drivetrain › K120 (MULTIDRIVE / CVT) › OIL PAN › 2018.10–2020.08
RM3620E _52 Drivetrain _076272 K120 MULTIDRIVE / CVT _0371715 OIL PAN A

K120 MULTIDRIVE / CVT  OIL PAN  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transaxle side cover sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Air bleed oil pump with motor assembly (w/ Stop and Start System) Stop and start system (Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

Hide 53896B 3.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Hide 51441 4.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51420 5.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737D 6.REMOVE FRONT FENDER APRON SEAL LH

Hide 7.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C394992

Remove the refill plug and gasket from the rear transaxle case sub-assembly.


b.
C394993

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly, and drain the fluid.


c.
C394994C01
2.375,0.844 2.656,0.844 true 2.219,0.771 2.448,1 0.229,0.229 10 false *1
*1 Overflow (CVT) Tube


Using a 6 mm hexagon socket wrench, remove the overflow (CVT) tube from the transaxle case sub-assembly.

HINT:

Removing the overflow (CVT) tube will drain all fluid in the transaxle case sub-assembly.



d.

Using a 6 mm hexagon socket wrench, install the overflow (CVT) tube to the transaxle case sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


e.

Using a 10 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the transaxle case sub-assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



f.

Temporarily install the gasket and refill plug to the rear transaxle case sub-assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 12601B 8.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 9.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 10.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 74404B 12.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 82121 13.DISCONNECT ENGINE WIRE

a.
C405189

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


b.

Detach the clamp.


c.
C405190

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


d.

Detach the 3 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


Hide 16261G 15.DISCONNECT NO. 1 WATER BY-PASS HOSE

Hide 32942N 16.REMOVE NO. 1 OIL COOLER OUTLET HOSE

a.
C405184

Slide the 2 hose clips and remove the No. 1 oil cooler outlet hose from the transmission oil cooler and oil cooler elbow sub-assembly.


Hide 32941R 17.REMOVE OIL COOLER INLET HOSE

a.
C405182

Slide the 2 hose clips and remove the oil cooler inlet hose from the transmission oil cooler and oil cooler elbow sub-assembly.


Hide 32901L 18.REMOVE OIL COOLER ELBOW SUB-ASSEMBLY

Hide 35015Y 19.REMOVE TRANSAXLE SIDE COVER SUB-ASSEMBLY

C405176

a.

Remove the 11 bolts and transaxle side cover sub-assembly from the transaxle case sub-assembly.


b.
C395511

Remove the O-ring from the transaxle side cover sub-assembly.