The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly removal/installation are shown below.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
If the front seat airbag assembly was deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
Replace any other damaged parts as necessary.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
for HV Model with Occupant Classification System:
for Gasoline Model with Occupant Classification System:
w/o Occupant Classification System:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
58410B
2.REMOVE DECK BOARD ASSEMBLY (for HV Model)
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
65351A
4.REMOVE BATTERY HOLE COVER (for HV Model)
71910A
5.REMOVE FRONT SEAT HEADREST ASSEMBLY
Remove the front seat headrest assembly from the front seat assembly LH.
72124
6.REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH
Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.
|
Place Hands Here |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Place your hands at the position shown in the illustration and slide in the removal direction (2) while pulling in the removal direction (1) to detach the guide and remove the front outer seat track bracket cover LH.
72124A
7.REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH
Use the same procedure described for the front outer seat track bracket cover LH.
72138N
8.REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH
Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the frontmost position.
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the rear outer seat track bracket cover LH.
72158E
9.REMOVE REAR INNER SEAT TRACK BRACKET COVER LH
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, detach the claw.
Tape the thin-bladed screwdriver tip before use.
Pull in the removal direction shown in the illustration to detach the guide and remove the rear inner seat track bracket cover LH.
10.REMOVE FRONT SEAT ASSEMBLY LH
Using a T50 "TORX" socket wrench, remove the 2 "TORX" screws.
Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the rearmost position.
Using a T50 "TORX" socket wrench, remove the 2 "TORX" screws.
Operate the reclining power seat switch knob and move the seatback of the front seat assembly LH perpendicular.
Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the center position.
Operate the slide and vertical power seat switch knob and move the front seat assembly LH to the uppermost position.
Disconnect the cable from the negative (-) auxiliary battery terminal.
for A25A-FKS:
for M20A-FKS:
for A25A-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Tilt the front seat assembly LH backward.
Be careful not to damage the front seat assembly LH or interior parts.
| *a | Front Seat Airbag Assembly LH Connector |
Disconnect the front seat airbag assembly LH connector.
Push down the white housing lock and slide the yellow CPA in the slide direction (1) as shown in the illustration.
| *a | Housing Lock | *b | Yellow CPA |
|
Slide in this Direction (1) |
|
Slide in this Direction (2) |
Do not pull while holding the wire harness.
Do not try to release the lock while holding down the top of the yellow CPA (A in the illustration), as this prevents the lock from being released.
Slide the yellow CPA in the slide direction (2) while pushing down the white housing lock again, and disconnect the connector.
Disconnect the other 2 connectors under the front seat assembly LH.
Detach the clamp.
Remove the front seat assembly LH as shown in the illustration.
2 or more people are required when carrying the front seat assembly LH out of the vehicle.
Protect the front seat legs.
Be careful not to damage the front seat assembly LH, body exterior or interior parts.