The display signal from each television camera is transmitted to the radio and display receiver assembly via the parking assist ECU.
When "!" mark is displayed on the parking assist ECU after the auxiliary battery terminal has been disconnected, correct the steering angle neutral point.
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio and display receiver assembly, be sure to replace it with a new one.
Communication malfunction DTC is output
Does not operate normally
Electrical devices are used in the cabin (noise may occur in the image).
The camera lens is frosted over (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night, etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The television camera assembly lens is scratched.
The television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.
Check if the same malfunction occurs when the panoramic view monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Rear view screen is not displayed. | A |
| Front view screen is not displayed. | B |
| Side monitor screen (LH side) is not displayed. | C |
| Side monitor screen (RH side) is not displayed. | D |
| Panoramic view monitor screen is not displayed. | E |
A
B
C
D
E
Disconnect the N24 parking assist ECU connector.
Disconnect the R15 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-33 (CB+) - R15-6 (CB+) | Always | Below 1 Ω |
| N24-29 (CV+) - R15-3 (CV+) | Always | Below 1 Ω |
| N24-30 (CV-) - R15-2 (CV-) | Always | Below 1 Ω |
| N24-32 (CGND) - R15-5 (CGND) | Always | Below 1 Ω |
| N24-31 (SGND) - Body ground | Always | 10 kΩ or higher |
| N24-33 (CB+) or R15-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| N24-29 (CV+) or R15-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| N24-30 (CV-) or R15-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| N24-32 (CGND) or R15-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-32 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N24-33 (CB+) - N24-32 (CGND) | Power switch on (IG) | 5.5 to 7.05 V |
| N24-33 (CB+) - N24-32 (CGND) | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the television camera assembly.
A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the television camera assembly.
The video waveform is constantly output when the power switch is on (ACC).
| Item | Content |
|---|---|
| Terminal No. (Symbol) | N24-29 (CV+) - N24-32 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (IG), panoramic view monitor switch on |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N24 parking assist ECU connector.
Disconnect the B12 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-15 (BCB+) - B12-6 (BCB+) | Always | Below 1 Ω |
| N24-36 (BCV+) - B12-3 (BCV+) | Always | Below 1 Ω |
| N24-13 (BCV-) - B12-2 (BCV-) | Always | Below 1 Ω |
| N24-37 (BGND) - B12-5 (BGND) | Always | Below 1 Ω |
| N24-14 (SGND) - Body ground | Always | 10 kΩ or higher |
| N24-15 (BCB+) or B12-6 (BCB+) - Body ground | Always | 10 kΩ or higher |
| N24-36 (BCV+) or B12-3 (BCV+) - Body ground | Always | 10 kΩ or higher |
| N24-13 (BCV-) or B12-2 (BCV-) - Body ground | Always | 10 kΩ or higher |
| N24-37 (BGND) or B12-5 (BGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-37 (BGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N24-15 (BCB+) - N24-37 (BGND) | Power switch on (IG) | 5.5 to 7.05 V |
| N24-15 (BCB+) - N24-37 (BGND) | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the front television camera assembly.
A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the front television camera assembly.
The video waveform is constantly output when the power switch is on (ACC).
| Item | Content |
|---|---|
| Terminal No. (Symbol) | N24-36 (BCV+) - N24-37 (BGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (IG), panoramic view monitor switch on |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Front)>REMOVAL
Disconnect the N24 parking assist ECU connector.
Disconnect the J13 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-12 (LCB+) - J13-3 (LCB+) | Always | Below 1 Ω |
| N24-10 (LCV+) - J13-4 (LCV+) | Always | Below 1 Ω |
| N24-34 (LCV-) - J13-12 (LCV-) | Always | Below 1 Ω |
| N24-35 (LGND) - J13-11 (LGND) | Always | Below 1 Ω |
| N24-12 (LCB+) or J13-3 (LCB+) - Body ground | Always | 10 kΩ or higher |
| N24-10 (LCV+) or J13-4 (LCV+) - Body ground | Always | 10 kΩ or higher |
| N24-34 (LCV-) or J13-12 (LCV-) - Body ground | Always | 10 kΩ or higher |
| N24-35 (LGND) or J13-11 (LGND) - Body ground | Always | 10 kΩ or higher |
| N24-11 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-35 (LGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N24-12 (LCB+) - N24-35 (LGND) | Power switch on (IG) | 5.5 to 7.05 V |
| N24-12 (LCB+) - N24-35 (LGND) | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly LH.
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
The video waveform is constantly output when the power switch is on (ACC).
| Item | Content |
|---|---|
| Tester Connection | N24-10 (LCV+) - N24-35 (LGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (IG), panoramic view monitor switch on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Side Television Camera Assembly LH) |
| *b | Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (SCB+) - J13-3 (LCB+) | Always | Below 1 Ω |
| A-3 (SCV+) - J13-4 (LCV+) | Always | Below 1 Ω |
| A-7 (SCV-) - J13-12 (LCV-) | Always | Below 1 Ω |
| A-5 (SGND) - J13-11 (LGND) | Always | Below 1 Ω |
| A-1 (SCB+) or J13-3 (LCB+) - Body ground | Always | 10 kΩ or higher |
| A-3 (SCV+) or J13-4 (LCV+) - Body ground | Always | 10 kΩ or higher |
| A-7 (SCV-) or J13-12 (LCV-) - Body ground | Always | 10 kΩ or higher |
| A-5 (SGND) or J13-11 (LGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
Malfunction does not reoccur (returns to normal)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N24 parking assist ECU connector.
Disconnect the I13 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-40 (RCB+) - I13-3 (RCB+) | Always | Below 1 Ω |
| N24-38 (RCV+) - I13-4 (RCV+) | Always | Below 1 Ω |
| N24-16 (RCV-) - I13-12 (RCV-) | Always | Below 1 Ω |
| N24-17 (RGND) - I13-11 (RGND) | Always | Below 1 Ω |
| N24-40 (RCB+) or I13-3 (RCB+) - Body ground | Always | 10 kΩ or higher |
| N24-38 (RCV+) or I13-4 (RCV+) - Body ground | Always | 10 kΩ or higher |
| N24-16 (RCV-) or I13-12 (RCV-) - Body ground | Always | 10 kΩ or higher |
| N24-17 (RGND) or I13-11 (RGND) - Body ground | Always | 10 kΩ or higher |
| N24-39 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-17 (RGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N24-40 (RCB+) - N24-17 (RGND) | Power switch on (IG) | 5.5 to 7.05 V |
| N24-40 (RCB+) - N24-17 (RGND) | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly RH.
The video waveform is constantly output when the power switch is on (ACC).
| Item | Content |
|---|---|
| Tester Connection | N24-38 (RCV+) - N24-17 (RGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (IG), panoramic view monitor switch on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Side Television Camera Assembly RH) |
| *b | Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH) |
Disconnect the side television camera assembly RH connector.
Disconnect the outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (SCB+) - I13-3 (RCB+) | Always | Below 1 Ω |
| B-3 (SCV+) - I13-4 (RCV+) | Always | Below 1 Ω |
| B-7 (SCV-) - I13-12 (RCV-) | Always | Below 1 Ω |
| B-5 (SGND) - I13-11 (RGND) | Always | Below 1 Ω |
| B-1 (SCB+) or I13-3 (RCB+) - Body ground | Always | 10 kΩ or higher |
| B-3 (SCV+) or I13-4 (RCV+) - Body ground | Always | 10 kΩ or higher |
| B-7 (SCV-) or I13-12 (RCV-) - Body ground | Always | 10 kΩ or higher |
| B-5 (SGND) or I13-11 (RGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
Malfunction does not reoccur (returns to normal)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the N24 parking assist ECU connector.
Disconnect the G2 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-7 (NS+) - G2-28 (V+) | Always | Below 1 Ω |
| N24-24 (NS-) - G2-29 (V-) | Always | Below 1 Ω |
| N24-6 (RSW+) - G2-18 (CSW+) | Always | Below 1 Ω |
| N24-7 (NS+) or G2-28 (V+) - Body ground | Always | 10 kΩ or higher |
| N24-24 (NS-) or G2-29 (V-) - Body ground | Always | 10 kΩ or higher |
| N24-8 (NSG) - Body ground | Always | 10 kΩ or higher |
| N24-6 (RSW+) or G2-18 (CSW+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the radio and display receiver assembly with a new.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG