The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
1.REMOVE REAR WHEEL
17430
2.REMOVE TAIL EXHAUST PIPE ASSEMBLY
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
for A25A-FXS:
Click hereEngine / Hybrid System>A25A-FXS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL
58327B
3.REMOVE MAIN MUFFLER HEAT INSULATOR
53896B
4.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
53895B
5.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
51441
6.REMOVE NO. 1 ENGINE UNDER COVER
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
51420
7.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL
58166A
8.REMOVE FRONT FLOOR COVER LH (w/ Floor Under Cover)
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL TANK (w/ Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL TANK>REMOVAL
58166A
9.REMOVE FRONT FLOOR COVER RH (w/ Floor Under Cover)
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL TANK (w/ Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL TANK>REMOVAL
58399D
10.REMOVE NO. 2 FLOOR UNDER COVER (w/ Floor Under Cover)
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL TANK (w/ Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL TANK>REMOVAL
58398F
11.REMOVE NO. 1 FLOOR UNDER COVER (w/ Floor Under Cover)
for A25A-FKS:
Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL TANK (w/ Canister Pump Module)>REMOVAL
for M20A-FKS:
Click hereEngine / Hybrid System>M20A-FKS (FUEL)>FUEL TANK>REMOVAL
48738C
12.REMOVE LOWER NO. 2 CONTROL ARM COVER LH (w/ Cover)
48737C
13.REMOVE LOWER NO. 2 CONTROL ARM COVER RH (w/ Cover)
Perform the same procedure as for the LH side.
47319F
14.SEPARATE REAR FLEXIBLE HOSE LH
Remove the bolt and separate the rear flexible hose LH from the rear flexible hose bracket.
47318F
15.SEPARATE REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
89408C
16.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
48840A
17.REMOVE REAR STABILIZER LINK ASSEMBLY LH
48830D
18.REMOVE REAR STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
48812
19.REMOVE REAR STABILIZER BAR
48231B
20.REMOVE REAR COIL SPRING LH
48231A
21.REMOVE REAR COIL SPRING RH
Perform the same procedure as for the LH side.
48258C
22.REMOVE REAR LOWER COIL SPRING INSULATOR LH
48258B
23.REMOVE REAR LOWER COIL SPRING INSULATOR RH
Perform the same procedure as for the LH side.
48740F
24.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH
48730F
25.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48720A
26.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH
48710A
27.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
48790
28.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH
Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.
Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.
48770A
29.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH
Use the same procedure as for the LH side.
51206A
30.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY
Disengage the 2 clamps to separate the height control sensor wire harness.
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment and Wooden Block Placement Location |
Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.
The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.
Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.
Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.
Slowly lower the rear suspension member sub-assembly.
When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.
Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.
48790
31.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH
48770A
32.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH
Perform the same procedure as for the LH side.
52272A
33.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)
| *a | Bend Portion |
Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.
Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.
Apply lubricant to the contact surfaces of the rear suspension member front body mounting cushion.
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.
Set the claws of SST into the rear suspension member sub-assembly securely as shown in the illustration.
Tighten SST slowly and evenly.
Be careful as the rear suspension member front body mounting cushion may fly out.
The rear suspension member front body mounting cushion cannot be reused.
Remove SST and the rear suspension member front body mounting cushion from the rear suspension member sub-assembly.
52271E
34.REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)
Perform the same procedure as for the LH side.
52276B
35.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH
Install SST as shown in the illustration.
Apply molybdenum grease to the threads and tip of the SST center bolt before use.
| *a | Hold |
|
Turn |
Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.
Tighten SST slowly and evenly.
Be careful as the rear suspension member rear body mount cushion LH may fly out.
The rear suspension member rear body mount cushion LH cannot be reused.
Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.
52275C
36.REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH
Perform the same procedure as for the LH side.
37.REMOVE HOLE PLUG
Remove the 6 hole plugs from the rear suspension member sub-assembly.
There are 2 different shapes of hole plug.