Home › Engine / Hybrid System › A25A-FXS (FUEL) › FUEL SYSTEM
RM3620E _51 Engine / Hybrid System _076684 A25A-FXS FUEL _0373219 FUEL SYSTEM L

A25A-FXS FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.

·
A357489

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the EFI MAIN NO. 2 relay:

i.

Remove the engine room relay block cover.


ii.

Remove the EFI MAIN NO. 2 relay.


iii.

Remove the front fender front splash shield LH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


iv.

Remove the front fender front splash shield RH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


v.

vi.

Remove the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


vii.
A436258C01
0.458,0.635 0.583,0.25 0.583,0.25 0.708,0.25 false 2.427,0.542 2.563,0.208 2.563,0.208 2.688,0.208 false 0.76,0.177 1.073,0.333 0.313,0.156 10 false *a 2.75,0.135 3.063,0.292 0.313,0.156 10 false *a
*a Lock Lever


Detach the claw and raise the lock lever to disconnect the No. 6 engine wire connector as shown in the illustration.


viii.

Connect the GTS to the DLC3.


ix.

Turn the power switch on (IG).


x.

Turn the GTS on.


xi.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

xii.

Start the engine. After the engine has stopped on its own, turn the power switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



xiii.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low), P017100 (System Too Lean), P319000 (Poor Engine Power), P319100 (Engine does not Start) or P319300 (Fuel Run Out) may be stored. Clear the DTCs before proceeding to the next step.




xiv.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


xv.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



xvi.
A436261C01
0.604,0.573 0.729,0.271 0.729,0.271 0.844,0.271 false 2.229,0.635 2.354,0.333 2.354,0.333 2.469,0.333 false 0.896,0.208 1.208,0.365 0.313,0.156 10 false *a 2.531,0.26 2.844,0.417 0.313,0.156 10 false *a
*a Lock Lever


Connect the No. 6 engine wire connector and push down the lock lever to attach the claw as shown in the illustration.


xvii.

Install the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


xviii.

xix.

Install the front fender front splash shield LH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


xx.

Install the front fender front splash shield RH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


xxi.

Install the EFI MAIN NO. 2 relay.


xxii.

Install the engine room relay block cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Remove the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


ii.

Remove the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


iii.

Remove the rear door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


iv.

Remove the No. 3 battery service cover board.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


v.

Remove the rear door scuff plate RH.


vi.

Remove the No. 2 battery service cover board.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


vii.

Remove the battery service cover board.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>REMOVAL


viii.

Remove the 3 bolts and rear floor service hole cover.


ix.
A436256C01
0.115,0.094 0.375,0.25 0.26,0.156 10 true *A 0.135,2.531 0.385,2.688 0.25,0.156 10 true *B
*A w/ Canister Pump Module
*B w/o Canister Pump Module


Disconnect the connector from the fuel suction with pump and gauge tube assembly.


x.

Remove the front fender front splash shield LH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


xi.

Remove the front fender front splash shield RH

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


xii.

xiii.

Remove the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


xiv.
A403901C02
0.458,0.635 0.583,0.25 0.583,0.25 0.708,0.25 false 2.427,0.542 2.563,0.208 2.563,0.208 2.688,0.208 false 0.76,0.177 1.073,0.333 0.313,0.156 10 false *a 2.75,0.135 3.063,0.292 0.313,0.156 10 false *a
*a Lock Lever


Detach the claw and raise the lock lever to disconnect the No. 6 engine wire connector as shown in the illustration.


xv.

Connect the GTS to the DLC3.


xvi.

Turn the power switch on (IG).


xvii.

Turn the GTS on.


xviii.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

xix.

Start the engine. After the engine has stopped on its own, turn the power switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



xx.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low), P017100 (System Too Lean), P319000 (Poor Engine Power), P319100 (Engine does not Start) or P319300 (Fuel Run Out) may be stored. Clear the DTCs before proceeding to the next step.




xxi.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


xxii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



xxiii.
A403902C02
0.604,0.573 0.729,0.271 0.729,0.271 0.844,0.271 false 2.229,0.635 2.354,0.333 2.354,0.333 2.469,0.333 false 0.896,0.208 1.208,0.365 0.313,0.156 10 false *a 2.531,0.26 2.844,0.417 0.313,0.156 10 false *a
*a Lock Lever


Connect the No. 6 engine wire connector and push down the lock lever to attach the claw as shown in the illustration.


xxiv.

Install the No. 2 engine under cover assembly.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


xxv.

xxvi.

Install the front fender front splash shield LH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


xxvii.

Install the front fender front splash shield RH.

Click hereEngine / Hybrid System>A25A-FXS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION


xxviii.

Connect the connector to the fuel suction with pump and gauge tube assembly.


xxix.

Install the rear floor service hole cover with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Securely install the rear floor service hole cover.



xxx.

Install the battery service cover board.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>INSTALLATION


xxxi.

Install the No. 2 battery service cover board.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>INSTALLATION


xxxii.

Install the rear door scuff plate RH.


xxxiii.

Install the No. 3 battery service cover board.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY BLOWER>INSTALLATION


xxxiv.

Install the rear door scuff plate LH.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


xxxv.

Install the rear seat cushion lock hook.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION


xxxvi.

Install the bench type rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel pump tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401631C03
0,0 0,0 false
V100135

Open
V100136

Pull


Clamp Type A (No. 1 Fuel Pipe Clamp):

Open the cover of the fuel pipe clamp and remove the fuel pipe clamp from the fuel tube connector.


ii.
A401632

Clamp Type B (Fuel Pipe Clamp):

Remove the fuel pipe clamp from the fuel tube connector.


iii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iv.
A403898C01
1.833,2.344 2.073,2.031 2.073,2.031 2.219,2.031 false 2.271,1.948 2.583,2.104 0.313,0.156 10 false *a
*a Retainer
V100135

Retainer Holding Position
V100136

Pull out


While holding the retainer at the positions shown in the illustration, pull up the retainer to detach the lock claws.

HINT:
A403900C01
1.677,0.698 1.833,0.698 1.833,0.698 2.042,0.99 false 1.833,0.365 1.979,0.365 1.979,0.365 2.323,0.875 false 1.667,0.271 1.979,0.427 0.313,0.156 10 false *a 1.51,0.615 1.823,0.771 0.313,0.156 10 false *b
*a Retainer
*b Protective Tape


If the lock claws of the retainer are difficult to detach, detach them using a screwdriver with its tip wrapped with protective tape.



v.
A403899C01
1.167,0.354 1.313,0.354 1.313,0.354 1.625,0.646 false 1.896,1.948 2.104,1.573 2.104,1.573 2.25,1.573 false 1.979,3.188 2.073,2.938 2.073,2.938 2.219,2.938 false 1.354,3.333 1.604,3.333 1.604,3.333 1.604,3.594 false 2.125,3.885 2.281,4.302 2.281,4.302 2.396,4.302 false 0.833,4.177 0.833,3.917 true 1.875,4.26 1.875,4.063 false 1.479,3.594 1.479,3.333 false 1,0.26 1.313,0.417 0.313,0.156 10 false *a 1.198,3.24 1.51,3.396 0.313,0.156 10 false *b 1.802,4.292 2.115,4.448 0.313,0.156 10 false *c 0.75,4.208 1.063,4.365 0.313,0.156 10 false *d 2.448,4.208 2.76,4.365 0.313,0.156 10 false *e 2.302,1.49 2.615,1.646 0.313,0.156 10 false *a 2.271,2.854 2.583,3.01 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Retainer Holding Position
V100136

Pull out
V100137

Pull off


Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.


vi.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




vii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


viii.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, and then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Clamp Type A (No. 1 Fuel Pipe Clamp):

Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.


iv.

Clamp Type B (Fuel Pipe Clamp):

Install the fuel pipe clamp to the fuel tube connector.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A369119C01
1.792,0.875 1.917,0.552 1.917,0.552 2.052,0.552 false 2.313,0.99 2.875,0.99 2.875,0.99 2.875,1.26 false 2.448,1.271 2.448,0.99 false 2.198,1.813 2.417,1.813 false 1.76,2.677 1.99,2.677 1.99,2.677 2.094,3.083 false 2.781,3.208 2.896,2.833 2.896,2.833 3.031,2.833 false 2.021,4.094 2.021,3.813 true 2.469,4.427 2.469,4.24 false 2.385,4.458 2.698,4.615 0.313,0.156 10 false *a 2.104,0.479 2.417,0.635 0.313,0.156 10 false *b 1.583,2.594 1.896,2.75 0.313,0.156 10 false *c 1.938,4.135 2.25,4.292 0.313,0.156 10 false *d 2.146,0.896 2.458,1.052 0.313,0.156 10 false *e 2.021,1.729 2.333,1.885 0.313,0.156 10 false *a 3.083,2.76 3.396,2.917 0.313,0.156 10 false *b
*a Retainer
*b Fuel Pipe
*c Fuel Tube Connector
*d O-ring
*e Claw
V100135

Push
V100136

Pull out
V100137

Pull off


Detach the 2 claws of the retainer. Pull out the retainer and disconnect the fuel tube connector from the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has an O-ring that seals the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A368840C01
1.281,1.969 1.927,1.969 1.927,1.969 1.927,2.208 false 1.49,2.219 1.49,1.969 false 1.167,2.781 1.458,2.781 false 0.99,2.698 1.302,2.854 0.313,0.156 10 false *a 1.104,1.896 1.417,2.052 0.313,0.156 10 false *b
*a Retainer
*b Claw
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, and then push in the retainer to engage the 2 claws.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A374322C01
2,2.823 2.167,3.021 2.167,3.021 2.281,3.021 false 1.385,3.208 1.573,3.208 1.573,3.208 1.677,3.458 false 1.448,4.469 1.448,4.146 false 1.302,4.469 1.521,4.469 1.521,4.469 1.521,4.146 false 2.469,4.385 2.344,4.385 2.344,4.385 2.219,4.167 false 1.938,1.99 1.938,1.208 true 2.333,2.938 2.646,3.094 0.313,0.156 10 false *a 1.146,4.385 1.458,4.542 0.313,0.156 10 false *b 1.229,3.115 1.542,3.271 0.313,0.156 10 false *c 2.531,4.313 2.844,4.469 0.313,0.156 10 false *d 1.854,2 2.167,2.156 0.313,0.156 10 false *e
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Tank Assembly
*e Claw
V100135

Push
V100136

Push
V100137

Pull off


Push the claw of the retainer, push the retainer of fuel tube connector, and then pull the fuel tube connector off of the fuel tank assembly.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.

If the fuel tube connector and fuel tank assembly are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel tank assembly carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel tank assembly).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A377514C01
1.708,0.292 1.823,0.292 1.823,0.292 1.969,0.74 false 1.542,0.198 1.854,0.354 0.313,0.156 10 false *a
*a Retainer
V100135

Pull out


Pull out the retainer until the retainer makes a "click" sound.


ii.
A377515C01
2.104,2.99 2.188,3.208 2.188,3.208 2.333,3.208 true 2.396,3.125 2.708,3.281 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel tank assembly, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


iii.

Connect the fuel lines and push in the retainer. Check that the fuel tube connector is securely connected by pulling on it.




h.
A289951C03
2.333,0.427 2.521,0.427 2.521,0.427 2.823,0.74 false 0.917,1.615 1.104,1.615 1.104,1.615 1.365,1.333 false 1.708,1.281 1.906,1.594 1.906,1.594 2.052,1.594 false 2.156,0.354 2.448,0.594 0.292,0.24 10 *a 2.115,1.531 2.438,1.792 0.323,0.26 10 *b 0.698,1.563 1,1.823 0.302,0.26 10 *c
*a Fuel Tube Connector
*b Nylon Tube
*c Ethylene Propylene Diene Monomer (EPDM) Rubber Protector


Observe the following precautions when handling a nylon tube:

NOTICE:
·

Do not twist the nylon tube of the fuel tube connector or fuel tube connector when connecting it.

·

Do not remove the Ethylene Propylene Diene Monomer (EPDM) rubber protector on the outside of the nylon tube.

·

Do not bend, twist, pinch or kink the nylon tube.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
·
A434652C01
0.771,1.698 0.438,1.698 false 0.677,3.656 0.344,3.656 false 0.094,0.125 0.406,0.281 0.313,0.156 10 false *A 0.135,2.552 0.448,2.708 0.313,0.156 10 false *B 0.26,1.604 0.573,1.76 0.313,0.156 10 false *a 0.167,3.552 0.479,3.708 0.313,0.156 10 false *a
*A w/ Canister Pump Module
*B w/o Canister Pump Module
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel sub-tank sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION