77020A
1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Install a new gasket to the fuel tank assembly.
Set the fuel suction with pump and gauge tube assembly to the fuel tank assembly.
Be careful not to bend the arm of the fuel sender gauge assembly.
To avoid applying excessive force to the tip of the fuel sender gauge assembly, tilt the fuel sub-tank sub-assembly diagonally and insert it into the fuel tank assembly as shown in the illustration.
| *1 | Plate Sub-assembly | *2 | Fuel Sub-tank Sub-assembly |
| *3 | Fuel Sender Gauge Assembly | - | - |
| *a | Protrusion |
| *b | Notch |
Align the protrusions of the fuel suction with pump and gauge tube assembly with the notches in the fuel tank assembly.
77144
2.INSTALL FUEL PUMP GAUGE RETAINER
Install the fuel pump gauge retainer.
While pressing down on the fuel suction with pump and gauge tube assembly, temporarily install the fuel pump gauge retainer.
| *a | SST (Plate) |
| *b | SST (Bolt) |
| *c | SST (Claw) |
| *d | Insertion Point |
Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
| *a | SST (Handle) |
| *b | Extension Bar |
| *c | SST (Plate) |
| *d | SST (Bolt) |
| *e | Triangle Mark (Fuel Tank Assembly) |
| *f | Triangle Mark (Fuel Pump Gauge Retainer) |
Install SST (handle) and an extension bar to SST (plate).
Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction with pump and gauge tube assembly to the fuel tank assembly.
When turning SST (handle), take care not to hit the console box assembly with your hands or SST (handle).
Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
Make sure that the fuel suction tube set gasket does not come off.
Attach the claw and install the No. 1 fuel tube clamp to the fuel pump gauge retainer.
77209C
3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Push the fuel tube joint of the fuel tank main tube sub-assembly, and install the tube joint clip.
| *1 | Tube Joint Clip |
| *a | Nylon Tube |
| *b | Fuel Tube Joint |
| *c | O-ring |
| *d | Correct |
| *e | Incorrect |
Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.
Check that the fuel tube joint is securely inserted to the end.
Check that the tube joint clip is on the collar of the fuel tube joint.
After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.
77026B
4.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction with pump and gauge tube assembly.
Click hereEngine / Hybrid System>A25A-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
58325E
5.INSTALL REAR FLOOR SERVICE HOLE COVER
Connect the 2 connectors to the fuel suction with pump and gauge tube assembly.
Install the rear floor service hole cover with the 3 bolts.
Return the floor carpet to its original position.
58903A
6.INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY
58464D
7.INSTALL BATTERY SERVICE COVER BOARD
58466J
8.INSTALL NO. 2 BATTERY SERVICE COVER BOARD
67917C
9.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
58467H
10.INSTALL NO. 3 BATTERY SERVICE COVER BOARD
67918E
11.INSTALL REAR DOOR SCUFF PLATE LH
72693
12.INSTALL REAR SEAT CUSHION LOCK HOOK
13.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
65351A
15.INSTALL BATTERY HOLE COVER
58416K
16.INSTALL REAR NO. 2 FLOOR BOARD
58410B
17.INSTALL DECK BOARD ASSEMBLY
18.INSPECT FOR FUEL LEAK
19.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing the fuel pump.