CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
| *A | except LHD, Manual Transaxle | *B | for LHD, Manual Transaxle |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Connect the instrument panel junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-11 (GND1) - Body ground | None - Body ground | Ground | Always | Below 1 Ω |
| A-30 (ACC) - Body ground | None - Body ground | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | None - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| A-32 (IG) - Body ground | None - Body ground | IG power supply | Ignition switch ON | 10.5 to 16 V*1
11 to 14 V*2 |
| Ignition switch off | Below 1 V | |||
| G44-1 (FLCY) - Body ground | R - Body ground | Front door courtesy light switch assembly LH input signal | Front door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| G44-6 (FRCY) - Body ground | BE - Body ground | Front door courtesy light switch assembly RH input signal | Front door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-13 (LCTY) - Body ground | None - Body ground | Rear door courtesy light switch assembly LH input signal | Rear door LH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-2 (RCTY) - Body ground | None - Body ground | Rear door courtesy light switch assembly RH input signal | Rear door RH closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| A-4 (BCTY) - Body ground | None - Body ground | Back door courtesy light switch signal | Back door closed (OFF) → open (ON) | 10 kΩ or higher → Below 1 Ω |
| G44-30 (HCTY) - Body ground | GR - Body ground | Engine hood courtesy switch input signal | Engine hood open (OFF) → closed (ON) | 10 kΩ or higher → Below 1 Ω |
| A-3 (KSW) - Body ground*3 | None - Body ground | Unlock warning switch input | Key not in key cylinder (OFF) → Key in key cylinder (ON) | 10 kΩ or higher → Below 1 Ω |
*1: for Manual Transaxle with Stop and Start System
*2: except *1
*3: w/o Entry and Start System
Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 4D-13 (LSFL) - Body ground | W - Body ground | Front door LH unlock detection switch input signal | Front door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door LH locked | Pulse generation | |||
| 4D-12 (LSFR) - Body ground | W - Body ground | Front door RH unlock detection switch input signal | Front door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door RH locked | Pulse generation | |||
| 4D-14 (LSWL) - Body ground | GR - Body ground | Rear door LH unlock detection switch input signal*1 | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door LH locked | Pulse generation | |||
| Rear door LH and RH unlock detection switch input signal*2 | Rear door LH or RH unlocked | Below 1 V | ||
| Ignition switch off, all doors closed and rear door LH and RH locked | Pulse generation | |||
| G43-20 (LSWR) - Body ground*1 | L - Body ground | Rear door RH unlock detection switch input signal | Rear door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door RH locked | Pulse generation | |||
| G44-7 (IND) - Body ground | B - Body ground | Security indicator light illumination | Security indicator light off | Below 2 V |
| Security indicator light blinking | Pulse generation | |||
| G45-12 (SSCL) - Body ground*3 | R - Body ground | Theft warning siren assembly drive | Theft warning siren assembly sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| G45-3 (SSW1) - Body ground*4 | L - Body ground | Intrusion sensor cancel switch signal | Intrusion sensor cancel switch on | Below 1 V |
| Intrusion sensor cancel switch off | Pulse generation | |||
| G45-14 (ISIF) - Body ground*4 | G - Body ground | Theft warning ultrasonic and tilt sensor signal input | ·
No moving object detected by sensor ·
Vehicle tilt not detected by sensor |
11 to 14 V |
| Theft deterrent system changes from disarmed state to armed preparation state | Pulse generation
(See Waveform 1) |
|||
| Any of the following conditions is met when the theft deterrent system is in armed preparation state
·
Any moving object detected by sensor ·
Vehicle tilt detected by sensor |
Pulse generation | |||
| 4A-20 (SH) - Body ground*5 | L - Body ground | Security horn drive | Security horn sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
| G45-1 (GPBS) - Body ground*6 | LG - Body ground | Glass breakage sensor signal | Glass breakage sensor normal | Below 2 V |
| Glass breakage sensor malfunctioning | 4.5 to 14 V | |||
| 4F-27 (HORN) - Body ground | W - Body ground | Vehicle horn drive | Vehicle horns sounding (Theft deterrent system is in alarm sounding state) | Pulse generation (Below 1 V ←→ 11 to 14 V) |
*1: w/ Memory
*2: w/o Memory
*3: w/o Security Horn Assembly
*4: w/ Intrusion Sensor Cancel Switch
*5: w/ Security Horn Assembly
*6: w/ Glass Breakage Sensor
Using an oscilloscope, check the waveform.
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
Waveform 1 (Reference)
| *a | IOUT Initial Signal | *b | IOUT Initial Response |
| *c | Approximately 1.0 Second | *d | Initial Diagnosis |
| *e | Approximately 1.0 to 1.6 Seconds | *f | Approximately 0.05 Seconds |
| *g | Approximately 5.5 Seconds | *h | Disarmed State |
| *i | Arming Preparation State | - | - |
| Item | Content |
|---|---|
| Tester Connection | G45-14 (ISIF) - Body ground |
| Tool Setting | 2 V/DIV., 100 ms./DIV. |
| Condition | Theft deterrent system changes from disarmed state to armed preparation state |
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
for HV Model:
for Gasoline Model: