Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM
RM3620E _53 Suspension _076850 TIRE PRESSURE MONITORING _0374400 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2179 Tire Pressure Monitor ECU Communication Stop Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Wire harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C408651E03
1.917,0.656 3.125,0.854 1.208,0.198 10 false ECU-IG1 NO. 4 4.698,1.396 5.01,1.594 0.313,0.198 10 false IG 2.073,3.604 4.469,3.781 2.396,0.177 10 false ECU-B NO. 2 (*3) 4.688,2.094 5.531,2.281 0.844,0.188 10 false +B 4.677,4.844 6.667,5.042 1.99,0.198 10 false PRG 1.219,4.927 1.677,5.125 0.458,0.198 10 false CPU 2.177,4.708 2.635,4.906 0.458,0.198 10 false PRG 2.583,4.719 2.896,4.917 0.313,0.198 10 false 11 4.406,4.708 4.563,4.906 0.156,0.198 10 false 5 0.448,5.667 0.906,5.865 0.458,0.198 10 false G45 0.458,5.854 3.531,6.063 3.073,0.208 10 false Main Body ECU (Multiplex Network Body ECU) 4.271,5.667 6.26,5.865 1.99,0.198 10 false M8 4.26,5.875 6.833,6.208 2.573,0.333 10 false Tire Pressure Warning ECU and Receiver 2.167,1.375 2.698,1.583 0.531,0.208 10 false IG41 2.219,2.125 2.792,2.333 0.573,0.208 10 false B41 2.583,1.26 2.74,1.458 0.156,0.198 10 false 3 2.583,2 2.74,2.198 0.156,0.198 10 false 2 0.615,2.604 1.854,2.771 1.24,0.167 10 false A32*5, G62*6 0.615,2.771 4.438,2.969 3.823,0.198 10 false Engine Stop and Start ECU 0.135,6.219 2.167,6.448 2.031,0.229 10 false *1: w/ Stop and Start System 0.146,6.531 2.208,6.792 2.063,0.26 10 false *2: w/o Stop and Start System 4.302,1.281 4.458,1.479 0.156,0.198 10 false 1 4.417,1.99 4.573,2.188 0.156,0.198 10 false 7 2.083,3.813 4.198,4.031 2.115,0.219 10 false ECU-DCC NO. 1 (*4) 3.302,1.5 3.615,1.698 0.313,0.198 10 false *1 3.323,2.25 3.635,2.448 0.313,0.198 10 false *1 3.292,0.354 3.604,0.552 0.313,0.198 10 false *2 3.333,3.365 3.646,3.563 0.313,0.198 10 false *2 0.146,6.844 6.76,7.229 6.615,0.385 10 false *3: Gasoline Model LHD, *2 and w/ Entry and Start System or Gasoline Model RHD and *2 or HV Model and w/ Entry and Start System 0.135,7.438 6.688,7.708 6.552,0.271 10 false *4: Gasoline Model LHD, *2 and w/o Entry and Start System or HV Model and w/o Entry and Start System 2.917,6.26 4.604,6.458 1.688,0.198 10 false *5: for LHD 2.906,6.552 4.594,6.75 1.688,0.198 10 false *6: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*


*: w/ Entry and Start System



PROCEDURE

1.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (OUTPUT WAVEFORM)
a.
C385231C15
1.219,0.219 1.615,0.448 0.396,0.229 0.865,1.729 1.156,1.094 true 0.208,0.229 0.521,0.427 0.313,0.198 10 false *a 2.875,3.406 3.188,3.604 0.313,0.198 10 false *b 0.719,1.771 1.125,2 0.406,0.229 10 false PRG 1.292,0.25 1.698,0.479 0.406,0.229 10 false G45
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))
*b GND


Using an oscilloscope, check the waveform.

NOTICE:

With the connector connected, check from the backside of the connector.


Standard Voltage:
Tester Connection Tool Setting Range Condition Specified Condition
G45-11 (PRG) - Body ground 5 V/DIV.5 ms./DIV. Ignition switch ON Waveform generation



Result:
Result Proceed to
Waveform is as shown in the illustration. (Waveform alternates between 9.8 V or higher and 1.2 V or less) A
Waveform does not change from 9.8 V or higher B
Waveform does not change from 1.2 V or less C



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)
2.CHECK TERMINAL VOLTAGE (TIRE PRESSURE WARNING ECU AND RECEIVER OUTPUT)
a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.
C409417C01
0.219,1.042 0.771,1.281 0.552,0.24 2.094,1.188 2.167,0.417 2.167,0.417 2.333,0.417 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 0.375,1.083 0.833,1.281 0.458,0.198 10 false G45 2.406,0.344 2.865,0.542 0.458,0.198 10 false PRG
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G45-11 (PRG) - Body ground Ignition switch ON 9.8 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
3.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Turn the ignition switch off.


b.

Disconnect the M8 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M8-5 (PRG) - G45-11 (PRG) Always Below 1 Ω
M8-5 (PRG) or G45-11 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.
C375025C37
1.49,0.188 1.885,0.448 0.396,0.26 0.625,1.771 1.198,1.417 true 1.229,1.167 0.74,1.177 false 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.469,1.823 0.927,2.021 0.458,0.198 10 false +B 1.594,0.219 2.052,0.417 0.458,0.198 10 false M8 0.542,1.104 1,1.302 0.458,0.198 10 false IG
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M8-7 (+B) - Body ground Always 10 to 16 V
M8-1 (IG) - Body ground Ignition switch ON 10 to 16 V



Result:
Proceed to
OK
NG (w/ Stop and Start System)
NG (w/o Stop and Start System)



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG (w/ Stop and Start System)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR